NefMoto > Technical > Data Logging > Take a look at those logs pls
Pages: 1 [2]
« previous next »
Author Topic: Take a look at those logs pls  (Read 21708 times)
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #15 on: April 15, 2012, 12:51:24 AM »
I did injectors repositioning and new log attached.
All logs and those logs are with NLS funtion.
« Last Edit: April 15, 2012, 12:54:55 AM by professor » Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #16 on: April 15, 2012, 03:57:56 AM »
Wrong log's format reattached.
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #17 on: April 17, 2012, 01:01:55 AM »
Up and good morning looking for some opinions  Smiley
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #18 on: May 25, 2012, 08:22:19 AM »
Compression ratio was measured again and problem revealed:
1st cylinder 11.8
2nd cylinder 9.8
3rd cylinder 11.2
4th cylinder 11.4

After feed cylinder 2 with oil, compression, measured again and reached 15. Cant be sure for the reason of the problem, but car doesn't burn oil or water so i guess should be a valve (probably exhaust one) problem.
Any thoughts?
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
ibizacupra
Full Member
***

Karma: +4/-10
Offline Offline

Posts: 111
« Reply #19 on: July 26, 2012, 04:07:42 AM »
Quote from: professor on May 25, 2012, 08:22:19 AM
Compression ratio was measured again and problem revealed:
1st cylinder 11.8
2nd cylinder 9.8
3rd cylinder 11.2
4th cylinder 11.4

After feed cylinder 2 with oil, compression, measured again and reached 15. Cant be sure for the reason of the problem, but car doesn't burn oil or water so i guess should be a valve (probably exhaust one) problem.
Any thoughts?

leak down test next then to try and determin where from..
cyl head off tho sound inevitable
Logged
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #20 on: July 26, 2012, 06:31:10 AM »
No leaks, vacuum system and ic were tested in every detail.
I ll check the bolts of the cyl head to see if all are tighten evenly.
More when done this.
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
prj
Hero Member
*****

Karma: +1072/-481
Offline Offline

Posts: 6037
« Reply #21 on: August 22, 2012, 03:11:11 AM »
Quote from: professor on July 26, 2012, 06:31:10 AM
No leaks, vacuum system and ic were tested in every detail.
I ll check the bolts of the cyl head to see if all are tighten evenly.
More when done this.


A leakdown test has absolutely nothing to do with your intake and IC.
Also, you got it the wrong way around. If you add oil and the Compression goes up, then it's usually the rings/bores.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #22 on: August 22, 2012, 04:39:43 PM »
Quote from: prj on August 22, 2012, 03:11:11 AM
A leakdown test has absolutely nothing to do with your intake and IC.
Also, you got it the wrong way around. If you add oil and the Compression goes up, then it's usually the rings/bores.

Correct, but we add much oil, 10-15ml so whenever the problem is wasn't revealed that way.
Now compression is ok, after using brand name engine cleaner, 11.8, 11.3, 11.6, 11.5 but knock volts on 2nd cyl are too much. More than 65V, varied from 40V to 72V, at WOT no matter pressure level (1bar, 1.7bar).
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #23 on: October 15, 2012, 06:51:17 AM »
So problem is now solved.

The root of the problem was loosen exhaust valve guides and 6 (a bit) bended exhaust valves too. Also intake valves had some deposits on its edges.

After machinery car works now very good.

Cheers.
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
ibizacupra
Full Member
***

Karma: +4/-10
Offline Offline

Posts: 111
« Reply #24 on: October 19, 2012, 09:20:56 AM »
Quote from: professor on October 15, 2012, 06:51:17 AM
So problem is now solved.

The root of the problem was loosen exhaust valve guides and 6 (a bit) bended exhaust valves too. Also intake valves had some deposits on its edges.

After machinery car works now very good.

Cheers.

thankyou for confirming and letting us know
Logged
Pages: 1 [2]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 26, 2024, 08:36:45 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.026 seconds with 16 queries. (Pretty URLs adds 0.001s, 0q)