NefMoto > Technical > NefMoto Software > Connects, but cant get passed security on bench. 2001 A4 018ch ecu
Pages: [1]
« previous next »
Author Topic: Connects, but cant get passed security on bench. 2001 A4 018ch ecu  (Read 17937 times)
Hindra
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14
I can connect, read and write fine with the ecu in the car, but with the same laptop/cable at my desk I cant get passed security. A buddy made the harness for me, he said the only thing he did different was no power in pin 21, I have no immobilizer. I am not trying bootmode, Ive got the ecu setup with 13.5v. Am I mistaken, will Nefmoto not do bench reads? For some reason I thought it could.
Logged
Auriaka
Full Member
***

Karma: +17/-2
Offline Offline

Posts: 113
« Reply #1 on: June 29, 2020, 11:39:08 PM »
I do bench reads with nefmoto with 018 CH all the time.

I can tell you what pins im using on my setup tomorrow, but it does work.
Logged
_nameless
Hero Member
*****

Karma: +347/-848
Offline Offline

Posts: 2861
« Reply #2 on: June 30, 2020, 12:43:10 AM »
Quote from: Hindra on June 29, 2020, 05:03:20 PM
I can connect, read and write fine with the ecu in the car, but with the same laptop/cable at my desk I cant get passed security. A buddy made the harness for me, he said the only thing he did different was no power in pin 21, I have no immobilizer. I am not trying bootmode, Ive got the ecu setup with 13.5v. Am I mistaken, will Nefmoto not do bench reads? For some reason I thought it could.
Post log from flasher
Logged
If you are broke or expecting free handouts DO NOT message me. I'll probably put you on blast if you do.
fknbrkn
Hero Member
*****

Karma: +207/-24
Offline Offline

Posts: 1494


mk4 1.8T AUM
« Reply #3 on: June 30, 2020, 10:40:36 AM »
21 and 121 should be wired
Logged
Hindra
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14
« Reply #4 on: June 30, 2020, 09:09:47 PM »
Quote from: Marty on June 30, 2020, 12:43:10 AM
Post log from flasher

Sorry I didnt do this with my original post.

30/Jun/2020 09:05:44.299: LOG: Setting Address: 0x01 KeyByte1: 0x6B KeyByte2: 0x0F
30/Jun/2020 09:05:44.359: LOG: Opened FTDI device.
30/Jun/2020 09:05:44.363: LOG: FTDI device info - Description: FT232R USB UART Serial Number: AH075J38 Device Type: FT_DEVICE_232R ID: 0x4036001 Device Flags: 0x0
30/Jun/2020 09:05:44.638: USER: Validated FTDI device is in dumb mode.
30/Jun/2020 09:05:44.655: LOG: Starting send receive thread.
30/Jun/2020 09:05:44.666: LOG: Send receive thread now started.
30/Jun/2020 09:05:44.672: USER: Disconnected
30/Jun/2020 09:05:44.700: LOG: Setting communication timings to defaults.
30/Jun/2020 09:05:44.706: LOG: Set timing parameters to defaults.
30/Jun/2020 09:05:44.711: USER: Connecting...
30/Jun/2020 09:05:44.737: LOG: Setting communication timings to defaults.
30/Jun/2020 09:05:44.744: USER: Starting slow init connection.
30/Jun/2020 09:05:47.350: USER: Connecting to address 0x01.
30/Jun/2020 09:05:49.529: USER: Slow init succeeded.
30/Jun/2020 09:05:49.534: LOG: Setting Address: 0x01 KeyByte1: 0x01 KeyByte2: 0x0A
30/Jun/2020 09:05:49.539: USER: Switching to KWP1281 session.
30/Jun/2020 09:05:49.711: LOG: KWP1281 read block
30/Jun/2020 09:05:49.775: LOG: KWP1281 sent block
30/Jun/2020 09:05:50.083: LOG: KWP1281 read block
30/Jun/2020 09:05:50.147: LOG: KWP1281 sent block
30/Jun/2020 09:05:50.325: LOG: KWP1281 read block
30/Jun/2020 09:05:50.389: LOG: KWP1281 sent block
30/Jun/2020 09:05:50.534: LOG: KWP1281 read block
30/Jun/2020 09:05:50.600: LOG: KWP1281 sent block
30/Jun/2020 09:05:50.636: LOG: KWP1281 read block
30/Jun/2020 09:05:50.700: LOG: KWP1281 sent block
30/Jun/2020 09:05:50.705: USER: KWP1281 connect info: 4B0906018CH 1.8L R4/5VT     G   0002 ~ö÷w
30/Jun/2020 09:05:52.210: USER: Connecting to address 0x01.
30/Jun/2020 09:05:54.397: USER: Slow init succeeded.
30/Jun/2020 09:05:54.403: LOG: Setting Address: 0x01 KeyByte1: 0x6F KeyByte2: 0x0F
30/Jun/2020 09:05:54.410: USER: Switching to KWP2000 session.
30/Jun/2020 09:05:54.416: USER: Connected
30/Jun/2020 09:05:56.951: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:05:56.993: LOG: Received message with service ID: TesterPresentPositiveReponse
30/Jun/2020 09:05:59.469: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:05:59.509: LOG: Received message with service ID: TesterPresentPositiveReponse
30/Jun/2020 09:06:01.989: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:06:02.033: LOG: Received message with service ID: TesterPresentPositiveReponse
30/Jun/2020 09:06:04.508: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:06:04.548: LOG: Received message with service ID: TesterPresentPositiveReponse
30/Jun/2020 09:06:07.026: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:06:07.062: LOG: Received message with service ID: TesterPresentPositiveReponse
30/Jun/2020 09:06:09.545: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:06:09.586: LOG: Received message with service ID: TesterPresentPositiveReponse
30/Jun/2020 09:06:10.092: LOG: User Prompt - Title: Confirm Full Read ECU Flash Memory Message: If you are ready to read, confirm the following things:
1) You have loaded a valid memory layout for the ECU.
2) The engine is not running.
Note: Some non-standard flash memory chips may prevent reading the flash memory.

Click OK to confirm, otherwise Cancel. Result: OK
30/Jun/2020 09:06:10.098: LOG: Disabling Windows sleep mode.
30/Jun/2020 09:06:10.113: USER: Reading ECU flash memory.
30/Jun/2020 09:06:10.137: LOG: Reading ECU identification option: 0x9C
30/Jun/2020 09:06:10.156: LOG: Sent message with service ID ReadECUIdentification
30/Jun/2020 09:06:10.205: LOG: Received message with service ID: ReadECUIdentificationPositiveResponse
30/Jun/2020 09:06:10.214: LOG: Read ECU identification option: 0x9C
30/Jun/2020 09:06:10.219: LOG: Successfully read ECU identification information
30/Jun/2020 09:06:10.233: USER: ECU reports programming session preconditions have been met.
30/Jun/2020 09:06:10.241: USER: Negotiating communication timings.
30/Jun/2020 09:06:10.246: LOG: Reading current communication timings.
30/Jun/2020 09:06:10.296: LOG: Sent message with service ID AccessTimingParameters
30/Jun/2020 09:06:10.337: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
30/Jun/2020 09:06:10.344: LOG: Set timing parameters to new values.
30/Jun/2020 09:06:10.349: LOG: Setting communication timing to defaults.
30/Jun/2020 09:06:10.399: LOG: Sent message with service ID AccessTimingParameters
30/Jun/2020 09:06:10.442: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
30/Jun/2020 09:06:10.448: LOG: Reading current communication timings.
30/Jun/2020 09:06:10.498: LOG: Sent message with service ID AccessTimingParameters
30/Jun/2020 09:06:10.546: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
30/Jun/2020 09:06:10.551: USER: Successfully changed to new communication timings.
30/Jun/2020 09:06:10.558: USER: Requesting security access.
30/Jun/2020 09:06:10.576: LOG: Sent message with service ID SecurityAccess
30/Jun/2020 09:06:10.614: LOG: Received message with service ID: NegativeResponse
30/Jun/2020 09:06:10.620: LOG: Received negative response for service ID: SecurityAccess, with response code: GeneralReject
30/Jun/2020 09:06:10.627: USER: ECU reports that security access request was rejected.
30/Jun/2020 09:06:10.635: LOG: Starting ProgrammingSession diagnostic session with 38400 baud rate.
30/Jun/2020 09:06:10.640: USER: Starting diagnostic session.
30/Jun/2020 09:06:10.662: LOG: Sent message with service ID StartDiagnosticSession
30/Jun/2020 09:06:10.704: LOG: Received message with service ID: NegativeResponse
30/Jun/2020 09:06:10.710: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
30/Jun/2020 09:06:10.744: LOG: Received message with service ID: NegativeResponse
30/Jun/2020 09:06:10.750: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
30/Jun/2020 09:06:10.784: LOG: Received message with service ID: NegativeResponse
30/Jun/2020 09:06:10.790: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
30/Jun/2020 09:06:10.824: LOG: Received message with service ID: NegativeResponse
30/Jun/2020 09:06:10.830: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
30/Jun/2020 09:06:10.864: LOG: Received message with service ID: NegativeResponse
30/Jun/2020 09:06:10.869: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending
30/Jun/2020 09:06:20.681: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:06:20.783: LOG: Message received no replies.
30/Jun/2020 09:06:20.788: LOG: Resending message. Send attempts: 2
30/Jun/2020 09:06:20.808: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:06:20.912: LOG: Message received no replies.
30/Jun/2020 09:06:20.917: LOG: Resending message. Send attempts: 3
30/Jun/2020 09:06:20.938: LOG: Sent message with service ID TesterPresent
30/Jun/2020 09:06:21.040: LOG: Message received no replies.
30/Jun/2020 09:06:21.045: LOG: Failed to send message 3 times, message send failed.
30/Jun/2020 09:06:21.050: USER: Disconnecting because no response was received for the Tester Present message.
30/Jun/2020 09:06:21.056: USER: Disconnected
30/Jun/2020 09:06:21.075: USER: Reading ECU flash memory failed.
30/Jun/2020 09:06:21.095: LOG: Closing FTDI device.
30/Jun/2020 09:06:21.112: LOG: Send receive thread now terminated.
30/Jun/2020 09:06:23.766: LOG: User Prompt - Title: Reading ECU Flash Memory Complete Message: Reading ECU flash memory failed. Result: OK
30/Jun/2020 09:06:23.772: USER: 100% complete.
30/Jun/2020 09:06:23.794: LOG: Restoring Windows sleep mode.
30/Jun/2020 09:06:29.109: LOG: Closing NefMoto VW Audi ME7 Flasher Logger 1.9.4.3
Logged
Hindra
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14
« Reply #5 on: June 30, 2020, 09:12:23 PM »
Quote from: fukenbroken on June 30, 2020, 10:40:36 AM
21 and 121 should be wired

I am fairly certain both of those are not wired, those are definitely needed for 018ch? I will get to that this weekend.

Edit: My buddy told me that there was no wire in pin 21 in the factory harness.
« Last Edit: July 01, 2020, 04:38:32 PM by Hindra » Logged
Hindra
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14
« Reply #6 on: July 02, 2020, 10:11:25 PM »
Quote from: fukenbroken on June 30, 2020, 10:40:36 AM
21 and 121 should be wired

You were right, put power on pin 121 and I can read and write from the bench harness. Thank you!
Logged
tombzwashere
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
« Reply #7 on: June 21, 2024, 02:26:22 PM »
would this be the same with 8e0909518AQ it wont let me flash
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • March 31, 2025, 08:20:28 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.045 seconds with 16 queries. (Pretty URLs adds 0.001s, 0q)