beou
Newbie
Karma: +0/-0
 Offline
Posts: 8
|
 |
« on: September 12, 2020, 06:48:06 AM »
|
|
|
Hello!!
Newbie here trying to flash my own citroen c3!
I have an EDC17c10, (lid opened and ready for boot mode)
When i am trying to ECU id or read, the mpps v18 prompts this:
'Please make sure that KLINE is connected to the ignition pin'
As i know, flashing an EDC17c10 with mpps does not require the k-line cable! Just CAN-H and CAN-L!
Do i have to use K line cable too?
Thanks!
|
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #1 on: September 12, 2020, 06:54:22 AM »
|
|
|
Hello!!
Newbie here trying to flash my own citroen c3!
I have an EDC17c10, (lid opened and ready for boot mode)
When i am trying to ECU id or read, the mpps v18 prompts this:
'Please make sure that KLINE is connected to the ignition pin'
As i know, flashing an EDC17c10 with mpps does not require the k-line cable! Just CAN-H and CAN-L!
Do i have to use K line cable too?
Thanks!
Clone? X-Boost Performance |
|
|
|
|
Logged
|
|
|
|
beou
Newbie
Karma: +0/-0
Offline
Posts: 8
|
|
« Reply #2 on: September 12, 2020, 07:06:23 AM »
|
|
|
Its a clone yes!!
|
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #3 on: September 12, 2020, 07:08:19 AM »
|
|
|
Its a clone yes!!
Make a second green kabel on the main green kabel for ignition X-Boost Performance |
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #4 on: September 12, 2020, 07:10:40 AM »
|
|
|
Make a second green kabel on the main green kabel for ignition
X-Boost Performance
and Picture of wiring please X-Boost Performance |
|
|
|
|
Logged
|
|
|
|
beou
Newbie
Karma: +0/-0
Offline
Posts: 8
|
|
« Reply #5 on: September 12, 2020, 07:19:32 AM »
|
|
|
Thanks for your reply!
EDC17c10 needs ground at pin 4,
12v at pin 2, and 12v too at pin 19!
Pin 19 is the ignition pin i assume!
CAN-H at pin 40 and CAN-L at pin 52!
In the mpps breakout cable, the CAN-H is the blue wire!
The CAN-L is the orange one!
K-line is green!
Why do i need two K-line cables?
In the photo, CAN-H and CAN-L are marked with different colours but i think that it doesnt matter!
|
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #6 on: September 12, 2020, 07:21:24 AM »
|
|
|
Thanks for your reply!
EDC17c10 needs ground at pin 4,
12v at pin 2, and 12v too at pin 19!
Pin 19 is the ignition pin i assume!
CAN-H at pin 40 and CAN-L at pin 52!
In the mpps breakout cable, the CAN-H is the blue wire!
The CAN-L is the orange one!
K-line is green!
Why do i need two K-line cables?
In the photo, CAN-H and CAN-L are marked with different colours but i think that it doesnt matter!
Do you have connected pin 9 and 12? X-Boost Performance |
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #7 on: September 12, 2020, 07:22:52 AM »
|
|
|
Sorry wrong text Where is the Pin Out of your seller for the mmps flasher?
X-Boost Performance
|
|
|
|
|
Logged
|
|
|
|
beou
Newbie
Karma: +0/-0
Offline
Posts: 8
|
|
« Reply #8 on: September 12, 2020, 07:35:41 AM »
|
|
|
Seller didnt provided any pinout!
I did a research and i think that the colors are correct!
I can confirm the the BLUE cable is CAN-H and ORANGE is CAN-L!
Used a multimeter and checked that the BLUE goes straight at pin 7 of the a1050c CAN transeiver chip!
So is the ORANGE connected straigth to pin 6 of the same chip.
|
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #9 on: September 12, 2020, 07:37:07 AM »
|
|
|
Seller didnt provided any pinout!
I did a research and i think that the colors are correct!
I can confirm the the BLUE cable is CAN-H and ORANGE is CAN-L!
Used a multimeter and checked that the BLUE goes straight at pin 7 of the a1050c CAN transeiver chip!
So is the ORANGE connected straigth to pin 6 of the same chip.
Wait i will later look at my KTag the Pinout for Bootmode right? it sould be the same X-Boost Performance |
|
|
|
|
Logged
|
|
|
|
beou
Newbie
Karma: +0/-0
Offline
Posts: 8
|
|
« Reply #10 on: September 12, 2020, 07:42:19 AM »
|
|
|
Thanks in advance for your effort!
I think that Ktag has different colors!
|
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #11 on: September 12, 2020, 09:46:04 AM »
|
|
|
Thanks in advance for your effort!
I think that Ktag has different colors!
no i dont Think so... you need Bootpin too....    X-Boost Performance |
|
|
|
|
Logged
|
|
|
|
beou
Newbie
Karma: +0/-0
Offline
Posts: 8
|
|
« Reply #12 on: September 12, 2020, 10:07:43 AM »
|
|
|
Thanks again!! I have already soldered a boot pin wire from the begining! But the result is the same!  |
|
|
|
|
Logged
|
|
|
|
xXxCryxXx
Full Member
Karma: +3/-17
Offline
Posts: 157
|
|
« Reply #13 on: September 12, 2020, 10:18:55 AM »
|
|
|
Thanks again!! I have already soldered a boot pin wire from the begining! But the result is the same! Maybe the Protocol of Clone MPPS is wrong .... that happens becuse Clone sorry M8 ... |
|
|
|
|
Logged
|
|
|
|
beou
Newbie
Karma: +0/-0
Offline
Posts: 8
|
|
« Reply #14 on: September 12, 2020, 10:27:04 AM »
|
|
|
OK! I will keep trying!
Thanks a lot for your help man!!
Cheers
|
|
|
|
|
Logged
|
|
|
|
|
