NefMoto > Technical > Tuning > Mafless and lambda correction B1 on idle
Pages: [1]
« previous next »
Author Topic: Mafless and lambda correction B1 on idle  (Read 7253 times)
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« on: April 28, 2012, 10:42:57 AM »
When you run mafless, with ltft's disabled, lambda correction on idle, shown on block 1 or 99,  in what values should vary?
I see +20%. Is logical?
Stft's are around +5% now with mafless.
Before mafless lftt's where 0.8-1.2% and stft's -0.2%.
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
RS-MAD
Jr. Member
**

Karma: +3/-1
Offline Offline

Posts: 46
« Reply #1 on: April 29, 2012, 01:59:39 AM »
You can tweak that , Im making my mods in +-7% range.
But if your long adapt is off , then I think there is no problem .....
Logged
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409
« Reply #2 on: April 29, 2012, 03:10:59 PM »
Any hint how to tweak it?
Logged
Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
RS-MAD
Jr. Member
**

Karma: +3/-1
Offline Offline

Posts: 46
« Reply #3 on: April 29, 2012, 04:37:16 PM »
Quote from: professor on April 29, 2012, 03:10:59 PM
Any hint how to tweak it?
KFLF
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #4 on: April 29, 2012, 04:45:33 PM »
I still see absolutely no good reason to run a MAFless setup.

If that's what you want, just go standalone
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
RS-MAD
Jr. Member
**

Karma: +3/-1
Offline Offline

Posts: 46
« Reply #5 on: May 01, 2012, 12:27:37 PM »
Quote from: nyet on April 29, 2012, 04:45:33 PM
I still see absolutely no good reason to run a MAFless setup.

If that's what you want, just go standalone
Find me standalone with Bosch like knock control , 100% checked and I will buy it Smiley
Logged
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617
« Reply #6 on: May 01, 2012, 01:01:57 PM »
fill me in here.  there are a number of top b5 s4's which use the me 7.1, aftermarket maf's, and push out 800+ hp.  i'm 100% with nyet in this boat.  what is the gain of this?  i see zero gain from this...   get a rs4 maf and stop trying to over-engineer.
Logged
RS-MAD
Jr. Member
**

Karma: +3/-1
Offline Offline

Posts: 46
« Reply #7 on: May 03, 2012, 11:21:51 AM »
Quote from: nehalem on May 01, 2012, 01:01:57 PM
fill me in here.  there are a number of top b5 s4's which use the me 7.1, aftermarket maf's, and push out 800+ hp.  i'm 100% with nyet in this boat.  what is the gain of this?  i see zero gain from this...   get a rs4 maf and stop trying to over-engineer.
ME7 is not only on thoose 2.7T , Im blowing stock maf like a crap on some of my engines .
If you want to stop to over-engineer then buy a TDI and drive safe Wink
Logged
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617
« Reply #8 on: May 03, 2012, 11:23:59 AM »
ok i'm going to stand back and just watch this thread, because while i'm critical i do find it interesting.
my point is that you can make 800whp with the maf, why bother eliminating it and dealing with hacks to repair a maf-intended ecu.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 30, 2024, 02:19:12 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.037 seconds with 16 queries. (Pretty URLs adds 0s, 0q)