Pages: [1]
Author Topic: Cannot connect to ecu  (Read 6065 times)
marty.h
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3


« on: June 09, 2012, 01:49:26 PM »

This is the log im getting any ideas where im going wrong

Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: 8D0907551E  2.7l V6/5VT     G   0002
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading all ECU info.
Starting diagnostic session.
Disconnecting because no response was received for the Tester Present message.
Disconnected
Reading all ECU info failed.
100% complete.
Restoring Windows sleep mode.
Starting loading of info.
Cancelling loading of info.
Starting loading of info.
Cancelling loading of info.
Switching to KWP2000 session.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: 8D0907551E  2.7l V6/5VT     G   0002
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disconnecting because no response was received for the Tester Present message.
Disconnected
Switching to KWP2000 session.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: 8D0907551E  2.7l V6/5VT     G   0002
Disabling Windows sleep mode.
Starting variable reading.
Starting diagnostic session.
Disconnecting because no response was received for the Tester Present message.
Disconnected
100% complete.
Stopped reading variables.
Restoring Windows sleep mode.
Starting loading of DTCs.
Cancelling loading of DTCs.
Switching to KWP2000 session.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting fast init connection.
Connecting to address 0x01.
Fast init sent, sending start communication request.
Start communication request did not receive any response.
Disconnected
Connecting...
Starting fast init connection.
Connecting to address 0x01.
Fast init sent, sending start communication request.
Start communication request did not receive any response.
Disconnected
Connecting...
Starting fast init connection.
Connecting to address 0x01.
Fast init sent, sending start communication request.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading all ECU DTCs.
Starting diagnostic session.
Diagnostic session mode does not match requested mode.
Successfully started diagnostic session.
Diagnostic session mode does not match requested mode.
Reading all ECU DTCs failed.
100% complete.
Restoring Windows sleep mode.
Disconnecting because no response was received for the Tester Present message.
Disconnected
Switching to KWP2000 session.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: 8D0907551E  2.7l V6/5VT     G   0002
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disconnecting because no response was received for the Tester Present message.
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: 8D0907551E  2.7l V6/5VT     G   0002
Connected
Disabling Windows sleep mode.
Reading all ECU info.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
0% complete.
25% complete.
50% complete.
75% complete.
100% complete.
Read 4 ECU info entries:
0x92, System Supplier ECU Hardware Number: 0261206376
   0x94, System Supplier ECU Software Number: 1037350221
   0x9B, Calibration Date: 8D0907551E  , 0002, 0x0000164F, 0x00000000, 0x009D, 2.7l V6/5VT    ,     
   0x9C, Calibration Equiment Software Number: 0x80030000
Restoring Windows sleep mode.
Disconnecting because no response was received for the Tester Present message.
Disconnected


Any ideas what is causing

Thanks in advance
Marty
Logged
marty.h
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3


« Reply #1 on: June 10, 2012, 11:49:08 AM »

Anyone ?

will this software work with a 1999 S4


Cheers
Marty
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.014 seconds with 16 queries. (Pretty URLs adds 0s, 0q)