marcellus
|
|
« Reply #225 on: December 11, 2012, 11:25:21 AM »
|
|
|
Share results please!
|
|
|
Logged
|
|
|
|
britishturbo
|
|
« Reply #226 on: December 11, 2012, 11:49:03 AM »
|
|
|
Share results please!
Oh I will for sure! Probably the weekend I'll get a few things on the car finished and start tuning. I have an LC-1 Wideband setup with Narrowband out going to B1 O2 sensor.
|
|
|
Logged
|
|
|
|
phila_dot
|
|
« Reply #227 on: December 11, 2012, 03:02:44 PM »
|
|
|
Good to hear that it's working out so far.
Does the trimming appear to be behaving normally?
|
|
|
Logged
|
|
|
|
marcellus
|
|
« Reply #228 on: December 11, 2012, 03:50:28 PM »
|
|
|
I think so. I should have some logs tomorrow morning.
|
|
|
Logged
|
|
|
|
britishturbo
|
|
« Reply #229 on: December 12, 2012, 05:17:12 PM »
|
|
|
I flashed my ecu just now with the "mono" lambda sensor changes. I can confirm that both banks show exactly the same O2 voltage, with only the Bank1 hooked up to the wideband. Good work!
|
|
|
Logged
|
|
|
|
marcellus
|
|
« Reply #230 on: December 15, 2012, 11:47:23 PM »
|
|
|
$260 shipped, I just ordered the PMAS, wiring pigtail and aluminum weld on flange. I am finally going to convert to blow through and hopefully get rid of the no-ideal intake setup.
|
|
|
Logged
|
|
|
|
britishturbo
|
|
« Reply #231 on: December 15, 2012, 11:55:09 PM »
|
|
|
Blow Through ftw!
|
|
|
Logged
|
|
|
|
marcellus
|
|
« Reply #232 on: December 20, 2012, 11:51:45 AM »
|
|
|
I am kind of nervous about the transfer function I came up with. Hopefully it will be a good place to start.
|
|
|
Logged
|
|
|
|
britishturbo
|
|
« Reply #233 on: December 20, 2012, 11:58:02 AM »
|
|
|
I am kind of nervous about the transfer function I came up with. Hopefully it will be a good place to start. I can check over it if you like :-)
|
|
|
Logged
|
|
|
|
marcellus
|
|
« Reply #234 on: December 20, 2012, 01:22:29 PM »
|
|
|
File I was messing with: see MLHFM
Using the HPX maf tool, calculated for 3" pipe......30 points transfer
Interpolated the 30 points to 512 for me7. The Low volt region .01 and a few points above have me kinda concerned. When I interpolated them I came up with a bunch of negative numbers. TunerPro made them 0, which is fine, its just something I think I m going to have to keep an eye on. I really need to start using ME7L so I can log MAF voltages, or better yet use one of the inputs from the zeitronix.
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #235 on: December 20, 2012, 01:24:15 PM »
|
|
|
MLOFS exists so that MLFHM can be all positive.
|
|
|
Logged
|
|
|
|
phila_dot
|
|
« Reply #236 on: December 20, 2012, 02:14:18 PM »
|
|
|
MLOFS exists so that MLFHM can be all positive.
More specifically for return flow detection.
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #237 on: December 20, 2012, 03:12:43 PM »
|
|
|
More specifically for return flow detection.
^this
|
|
|
Logged
|
|
|
|
erroob0977
Full Member
Karma: +12/-0
Offline
Posts: 66
|
|
« Reply #238 on: December 20, 2012, 08:57:41 PM »
|
|
|
File I was messing with: see MLHFM
Using the HPX maf tool, calculated for 3" pipe......30 points transfer
Interpolated the 30 points to 512 for me7. The Low volt region .01 and a few points above have me kinda concerned. When I interpolated them I came up with a bunch of negative numbers. TunerPro made them 0, which is fine, its just something I think I m going to have to keep an eye on. I really need to start using ME7L so I can log MAF voltages, or better yet use one of the inputs from the zeitronix.
I'm using the HPX sensor too and the MAF curve I ended up with is a good bit different than the interpolated curve I started with. However I'm using a mostly stock air box (just with holes cut in it) and with KFKHFM all set to 1, so I kinda worked the airbox's flow characteristics into my MAF curve. There's still a few rpm/load spots I have to fix up with KFKHFM but overall I think doing it the way I did got me a much more accurate reading with my set-up. I would definitely suggest trying to get ME7L working, being able to log MAF voltage, g/s, fuel trims + Zeitronix AFR made getting everything dialed in pretty easy.
|
|
|
Logged
|
2004 A6 2.7T 6MT: Built motor with SRM RS6/K24s on E85
|
|
|
marcellus
|
|
« Reply #239 on: December 20, 2012, 09:31:25 PM »
|
|
|
I'm using the HPX sensor too and the MAF curve I ended up with is a good bit different than the interpolated curve I started with. However I'm using a mostly stock air box (just with holes cut in it) and with KFKHFM all set to 1, so I kinda worked the airbox's flow characteristics into my MAF curve. There's still a few rpm/load spots I have to fix up with KFKHFM but overall I think doing it the way I did got me a much more accurate reading with my set-up. I would definitely suggest trying to get ME7L working, being able to log MAF voltage, g/s, fuel trims + Zeitronix AFR made getting everything dialed in pretty easy.
Would you mind sharing your Mlhfm?
|
|
|
Logged
|
|
|
|
|