Pages: [1] 2
Author Topic: noob Project stage 1 1.8t  (Read 6164 times)
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« on: November 11, 2022, 01:57:22 AM »

Hi,I am looking to do a stage 1 and adjustment for E85. thank you in advance for the help

A4B5 2000AWT 1.8t 4B0906018R 0261206539 1037354801

0280158117
Injectors flow rate =      630   cc/min         


      KRKTE pump fuel =      0.05192345     

Ethanol content                       -->            75   %   
                 
Stoich value on Ethanol       -->            10.425     

      KRKTE ethanol =      0.0732158

TVUB
8v 3.2
10v 1.61
12v 1.155
14v 0.75
16v 0.540
I'm going up
pump 340l/h
0280158117
FRP 4BAR STOCK

I try to group everything here so as not to invade the forum with my noob questions
« Last Edit: January 20, 2023, 12:02:41 PM by JeanAwt » Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
adam-
Hero Member
*****

Karma: +124/-33
Offline Offline

Posts: 2179


« Reply #1 on: November 11, 2022, 12:38:41 PM »

Read the wiki.
Logged
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1282



« Reply #2 on: November 11, 2022, 02:07:49 PM »

What ^ said. But LDRXN and other stuff. Go check it.

With E85 you need to change krkte and some injector tuning, but you can safely set timings to kfzwop usually.
Everything you asked is on the forum
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« Reply #3 on: November 12, 2022, 03:59:40 AM »

yes of course
 KRKTE
TVUB
KVB
LDRXN

but for the boost there must be other maps to modify?
LDRXNZK....
I have a few maps on my xdf but the units and axes are not all good. Can someone look at it please?
« Last Edit: January 20, 2023, 12:04:55 PM by JeanAwt » Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
TeknoFi
Full Member
***

Karma: +1/-3
Offline Offline

Posts: 85


« Reply #4 on: November 12, 2022, 05:30:01 AM »

I don't think anyone bother help if you don't even tell me what your ecu part number is, now we have to dig it out from your binary. don't hide it.


Btw, your injectors don't go very far with ethanol. Increasing the power ends up very short with them if you want it to run on ethanol.
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« Reply #5 on: November 12, 2022, 05:56:25 AM »

thank you
I modified with ecu number.630cc are too small for e85 and a bit more boost?
I have the stock K03 to remain reliable how much can I put 0.8 /0.9 bars in it?
Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
TeknoFi
Full Member
***

Karma: +1/-3
Offline Offline

Posts: 85


« Reply #6 on: November 12, 2022, 08:49:04 PM »

thank you
I modified with ecu number.630cc are too small for e85 and a bit more boost?
I have the stock K03 to remain reliable how much can I put 0.8 /0.9 bars in it?

ah nevermind i read injectors number wrong. They're fine.

I updated your XDF in another thread.
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« Reply #7 on: November 13, 2022, 12:13:55 AM »

thank you very much TeKnoFi.
LDRXNZK can remain original? is it protection? does it lower the pressure in the event of a blow?
Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« Reply #8 on: November 13, 2022, 12:50:11 AM »

I admit my first reading of the ecu went well in 7 minutes. but I worry a little more about the writing. because I need it to go to work  Undecided. maybe I should buy one backup ecu at 100 euros? because given my level I have a lot of log tests and adjustments to do. if the ecu crashes it's easy to put back in original boot mode? by obd

and for the cold start with E85. where should I start looking?
is there a map for the warmup? Huh

thank
Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
adam-
Hero Member
*****

Karma: +124/-33
Offline Offline

Posts: 2179


« Reply #9 on: November 13, 2022, 03:42:43 AM »

Yes, get a spare.  Learn how to bootmode and do it before you need it.

Yes, there are warmup maps.
Logged
TeknoFi
Full Member
***

Karma: +1/-3
Offline Offline

Posts: 85


« Reply #10 on: November 13, 2022, 05:07:59 AM »

but I worry a little more about the writing. because I need it to go to work  Undecided. maybe I should buy one backup ecu at 100 euros? because given my level I have a lot of log tests and adjustments to do. if the ecu crashes it's easy to put back in original boot mode? by obd


If you are going to do lot of writing (like me), consider doing permanent wiring the ecu with "switchable" boot mode. So that boot mode can be turned on at any time while ecu is attached in the car. I made a small hole through the ecu shell and sealed it, so whenever I want I can get the ecu into boot mode and do a repair via obd if normal writing fails (common with mpps  Lips sealed)
« Last Edit: November 13, 2022, 05:10:30 AM by TeknoFi » Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« Reply #11 on: November 13, 2022, 05:46:24 AM »

I'm interested, I thought the bootmode was as simple as reading with nefmoto since there is the option. how does it work? soldering to do? Huh
Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« Reply #12 on: November 13, 2022, 07:31:34 AM »

the software version must absolutely match?
I have: 1037354801
can i clone on
1037354735?
by obd is it possible?
the ecu for sale on ebay not always the software number
Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1282



« Reply #13 on: November 13, 2022, 05:12:32 PM »

Same bootrom version and pcb design files can be crossflashed without any issues. Pretty much anything but please dont make me look up all the info.
Post the whole output from me7check of bins..

It looks like that is even the same ecu so one of the softs is newer so tldr you can. Dont forget about your eeprom
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242


« Reply #14 on: November 14, 2022, 06:10:43 AM »

hi,I ordered a spare ecu. how do you read the eprom ecu? I understood that it is necessary to be in bootmode (pin 24 to the mass or by obd which software?) for the moment I manage to read the eprom cluster with vag commander. I equipped myself with me7eeprom me7_95040
but I am far from having read everything and understood everything. I have plenty to do


sorry for my google translate
Logged

A4 B5 avant 1.8T 2000 NO QUATTRO
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)