Hi Guys , just used this great software for the first time  , and running into problems reading the ECU


06/Jul/2012 07:27:43.453: LOG: Set timing parameters to defaults.
06/Jul/2012 07:27:43.484: LOG: Sent message with service ID TesterPresent
06/Jul/2012 07:27:43.484: LOG: Changed diagnostic session type to: ProgrammingSession
06/Jul/2012 07:27:43.484: LOG: ECU requesting specific baud rate: 124800
06/Jul/2012 07:27:43.484: USER: Successfully started diagnostic session.
06/Jul/2012 07:27:43.484: USER: Negotiating communication timings.
06/Jul/2012 07:27:43.484: LOG: Reading current communication timings.
06/Jul/2012 07:27:45.484: LOG: Message received no replies.
06/Jul/2012 07:27:45.484: LOG: Resending message. Send attempts: 2
06/Jul/2012 07:27:45.500: LOG: Sent message with service ID TesterPresent
06/Jul/2012 07:27:45.546: LOG: Received message with service ID: TesterPresentPositiveReponse
06/Jul/2012 07:27:45.609: LOG: Sent message with service ID AccessTimingParameters
06/Jul/2012 07:27:45.656: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
06/Jul/2012 07:27:45.656: LOG: Set timing parameters to new values.
06/Jul/2012 07:27:45.656: LOG: Reading communication timing limits.
06/Jul/2012 07:27:45.718: LOG: Sent message with service ID AccessTimingParameters
06/Jul/2012 07:27:45.765: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
06/Jul/2012 07:27:45.765: LOG: Requesting communication at timing limits.
06/Jul/2012 07:27:45.781: LOG: Sent message with service ID AccessTimingParameters
06/Jul/2012 07:27:45.828: LOG: Received message with service ID: AccessTimingParametersPositiveResponse
06/Jul/2012 07:27:45.828: USER: Successfully changed to new communication timings.
06/Jul/2012 07:27:45.828: USER: Requesting security access.
06/Jul/2012 07:27:45.843: LOG: Sent message with service ID SecurityAccess
06/Jul/2012 07:27:45.859: LOG: Received message with service ID: SecurityAccessPositiveResponse
06/Jul/2012 07:27:45.859: USER: Security access granted.
06/Jul/2012 07:27:45.859: USER: Validating flash memory starts at 0x00800000 and ends at 0x00900000.
06/Jul/2012 07:27:45.937: LOG: Sent message with service ID RequestUpload
06/Jul/2012 07:27:45.968: LOG: Received message with service ID: NegativeResponse
06/Jul/2012 07:27:45.968: LOG: Received negative response for service ID: RequestUpload, with response code: SecurityAccessDenied_SecurityAccessRequested
06/Jul/2012 07:27:45.968: USER: Validation failed, ECU reports that security access is not granted.
06/Jul/2012 07:27:45.968: USER: Memory layout validation failed.
06/Jul/2012 07:27:48.453: LOG: Sent message with service ID TesterPresent
06/Jul/2012 07:27:48.468: LOG: Received message with service ID: TesterPresentPositiveReponse
06/Jul/2012 07:27:50.015: LOG: User Prompt - Title: Unable to validate memory layout Message: Unable to validate memory layout. Do you want to continue reading flash memory without validating the memory layout? Result: OK
06/Jul/2012 07:27:50.015: USER: Starting to read data block.
06/Jul/2012 07:27:50.015: USER: Requesting upload from ECU for address range 0x00800000 to 0x0080FFFF.
06/Jul/2012 07:27:50.046: LOG: Sent message with service ID RequestUpload
06/Jul/2012 07:27:50.062: LOG: Received message with service ID: NegativeResponse
06/Jul/2012 07:27:50.062: LOG: Received negative response for service ID: RequestUpload, with response code: SecurityAccessDenied_SecurityAccessRequested
06/Jul/2012 07:27:50.109: USER: Request upload from ECU failed, ECU reports security access has not been granted.
06/Jul/2012 07:27:50.109: USER: Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete.
06/Jul/2012 07:27:50.171: LOG: Validating flashed data checksum for address range 0x00900000 to 0x00900001.
06/Jul/2012 07:27:50.187: LOG: Sent message with service ID StartRoutineByLocalIdentifier
06/Jul/2012 07:27:50.218: LOG: Received message with service ID: StartRoutineByLocalIdentifierPositiveResponse
06/Jul/2012 07:27:50.234: LOG: Sent message with service ID RequestRoutineResultsByLocalIdentifier
06/Jul/2012 07:27:50.265: LOG: Received message with service ID: NegativeResponse
06/Jul/2012 07:27:50.265: LOG: Received negative response for service ID: RequestRoutineResultsByLocalIdentifier, with response code: BlockTransferDataChecksumError
06/Jul/2012 07:27:50.265: LOG: Checksum is incorrect.
06/Jul/2012 07:27:50.265: USER: Finished forcing ECU to recognize that failed read operation is complete.
06/Jul/2012 07:27:50.265: USER: Reading ECU flash memory failed.
06/Jul/2012 07:27:52.750: LOG: Sent message with service ID TesterPresent
06/Jul/2012 07:27:52.781: LOG: Received message with service ID: TesterPresentPositiveReponse
06/Jul/2012 07:27:55.265: LOG: Sent message with service ID TesterPresent
06/Jul/2012 07:27:55.296: LOG: Received message with service ID: TesterPresentPositiveReponse
06/Jul/2012 07:27:56.468: LOG: User Prompt - Title: Reading ECU Flash Memory Complete Message: Reading ECU flash memory failed. Result: OK
06/Jul/2012 07:27:56.468: USER: 100% complete.
06/Jul/2012 07:27:56.500: USER: Restoring Windows sleep mode.
06/Jul/2012 07:27:57.781: LOG: Sent message with service ID TesterPresent
06/Jul/2012 07:27:57.796: LOG: Received message with service ID: TesterPresentPositiveReponse
06/Jul/2012 07:28:00.296: LOG: Sent message with service ID TesterPresent
06/Jul/2012 07:28:00.328: LOG: Received message with service ID: TesterPresentPositiveReponse
06/Jul/2012 07:28:00.718: USER: Disconnecting...
06/Jul/2012 07:28:00.781: LOG: Sent message with service ID StopCommunication
06/Jul/2012 07:28:00.796: LOG: Received message with service ID: StopCommunicationPositiveResponse
06/Jul/2012 07:28:00.796: USER: Disconnected
06/Jul/2012 07:28:00.875: LOG: Closing FTDI device.
06/Jul/2012 07:28:00.890: LOG: Send receive thread now terminated.
06/Jul/2012 07:41:15.312: LOG: Opening NefMoto VW Audi ME7 Flasher Logger 1.9.3.2
06/Jul/2012 07:41:15.453: LOG: Cannot load license file, file does not exist: C:\Documents and Settings\Administrator\Application Data\Nefarious Motorsports\NefMoto VW Audi ME7 Flasher Logger\ImportedLicenses.License.dat
06/Jul/2012 07:41:15.500: LOG: Opened NefMoto VW Audi ME7 Flasher Logger 1.9.3.2

any one point me in the right direction 

Im having a issue too. I have flashed my car a month ago on the older realease at that time. I was able to connect and save and flash a file. I was also able to use APR immo program and it read and write my codes.

I than again connect a few days ago and checked and cleared CEL. After that I installed new realease 1.9.3.2 or w.e. and now I am having problems. At first it would only connect while ignition was off but got error like stated about security. Then it would only connect if you had ignition on and while trying to connect turn ignition off it would connect but not flash. Now its will do the last thing I said and not connect at all. VCDS lite will not work now.

I will provide a log in a few mintues when I try something new. I was thinking my cable is bad. I am using a blue with sliver cable Ebay cable and I borrowed my friends ross tech usb-II or w.e. and vCDS workes fine and neffmoto comes up as a cable but can't be used. So I'm not sure if the ebay cable is fauilty.

thanks

  I fixed it !!  , when I do the fast init , it connects at 124800, but before I ask it to read , change it down to 9600 and it connects and reads  , happy days !!
now all I need is a laptop with a battery that will last more than 10 minutes lol, so I can create an original file .

woohoo