NefMoto > Technical > NefMoto Software > cant erase flash
Pages: [1]
« previous next »
Author Topic: cant erase flash  (Read 8903 times)
tnel20
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 139
« on: July 18, 2012, 07:20:51 AM »
here is what i get

i can read the file just fine but when i go to flash it it just sit there on sending request to erase
Logged
tnel20
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 139
« Reply #1 on: July 18, 2012, 08:05:51 AM »
Ahh not happy now. canceled the program because it was jsut sitting at the request to erase and tried to start and no luck
Logged
tnel20
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 139
« Reply #2 on: July 19, 2012, 10:00:49 AM »
Look at my part number
Logged
matchew
Hero Member
*****

Karma: +47/-22
Offline Offline

Posts: 503
« Reply #3 on: July 19, 2012, 10:27:00 AM »
The ECU will accept a flash in that state.
Logged
tnel20
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 139
« Reply #4 on: July 20, 2012, 08:30:10 AM »
i wish it would but no luck , jason on here is heading over tonight to see if we can get it working.
Logged
gremlin
Hero Member
*****

Karma: +196/-9
Offline Offline

Posts: 653
« Reply #5 on: July 20, 2012, 09:21:51 AM »
Quote from: tnel20 on July 20, 2012, 08:30:10 AM
i wish it would but no luck

This screen shows, that ECU is locked in "programm mode"
Waiting for help you cаn open ECU-box and check follows:
1. No additional crypt module installed
2. Flash chip has no visual manual soldering vestige
3. Flash chip has Am29F800BB marking (not ...800BT)
Logged
tnel20
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 139
« Reply #6 on: July 20, 2012, 07:02:13 PM »
Well jason came to my work to help me out . the chip i have installed was a AM29F800BB-70SI  not the AM29F800BB-70SD that is used by the factory . the ecu had a giac chip in it and i have infinic install a new chip in it and he installed the AM29F800BB-70SI and flashed it for me then mailed it back. i have tried to use older version of nefmoto and it woul dnever flash and the new version got it stuck in program mode.
Jason was able to boot mode flash it with galletto cable and software. then we tried to bench flash again with nefmoto and it failed so we flashed again with galletto. I dont know about chips and Jason really didnt know what the difference might be but it was unabe to flash through dumb cable mode.
Logged
Jason
Hero Member
*****

Karma: +38/-0
Offline Offline

Posts: 500


Breaks everything!
« Reply #7 on: July 23, 2012, 01:54:26 PM »
One thing I forgot to try was flashing my serial eeprom over to see if there is something wrong with your e2p...   I don't know if that could ever be an issue for flashing.  You could do that now with your KKL cable and ArgDub's utility - let me know if you need help... Otherwise I'll be back in your area on the 4th and we can try flashing my e2p.

Galletto non-boot mode flashed just fine too, but NefMoto would not flash.

I think the SD and SI designations have to do with environmental conditions (heat) but I'm not sure.
Logged
tnel20
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 139
« Reply #8 on: July 24, 2012, 12:41:43 PM »
yeah send over those links you were talking about and i'll try it out
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 23, 2024, 12:36:13 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.039 seconds with 18 queries. (Pretty URLs adds 0s, 0q)