NefMoto > Technical > Reverse Engineering > Adapt software for changed crankshaft sensor location
Pages: [1]
« previous next »
Author Topic: Adapt software for changed crankshaft sensor location  (Read 2267 times)
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« on: April 22, 2024, 10:31:28 AM »
Short long story, I have 6HP on M7.1
Now I want to change gearbox, but I don't want to relocate sensor (6HP have sensor location like manual gearbox) and on my curent gearbox I need to relocate sensor to be in same position like on 5HP

Is it posible to change that in software? To tell ECU that sensor is on different angle?
« Last Edit: April 22, 2024, 11:38:04 AM by BlackT » Logged
dus
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« Reply #1 on: April 23, 2024, 12:49:54 AM »
one mechanic I know who assembled such cars said that yes, it is possible. as well as PWM control of the fan block. he didn't change anything, just connected the wiring and everything worked. the flywheel remained original from 2.7
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #2 on: April 24, 2024, 02:35:29 AM »
What you mean by he didn't change anything?
Logged
dus
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« Reply #3 on: April 25, 2024, 11:46:25 PM »
without modification of the flywheel or gearbox housing. without replacing the fan control unit
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #4 on: April 26, 2024, 10:53:28 AM »
What fan control unit have with this?
You say he only put 6HP gearbox and car is starting driving?
Logged
dus
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« Reply #5 on: April 27, 2024, 12:42:27 AM »
he talked about a4 8ะต
yes
Logged
kacperoooni
Full Member
***

Karma: +9/-2
Offline Offline

Posts: 126
« Reply #6 on: May 08, 2024, 03:36:10 AM »
Quote from: dus on April 23, 2024, 12:49:54 AM
one mechanic I know who assembled such cars said that yes, it is possible. as well as PWM control of the fan block. he didn't change anything, just connected the wiring and everything worked. the flywheel remained original from 2.7

Liar.
Logged
kacperoooni
Full Member
***

Karma: +9/-2
Offline Offline

Posts: 126
« Reply #7 on: May 08, 2024, 03:40:14 AM »
Quote from: BlackT on April 22, 2024, 10:31:28 AM
Short long story, I have 6HP on M7.1
Now I want to change gearbox, but I don't want to relocate sensor (6HP have sensor location like manual gearbox) and on my curent gearbox I need to relocate sensor to be in same position like on 5HP

Is it posible to change that in software? To tell ECU that sensor is on different angle?

You need to find in IDA constant GDWRT
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2800
« Reply #8 on: May 09, 2024, 09:46:55 AM »
Easiest solution would be to redrill the flex plate for the correct offset
Logged
Giving your mom a tuneup
dus
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« Reply #9 on: May 10, 2024, 12:04:29 AM »
078105323Q as well
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #10 on: May 10, 2024, 10:48:26 AM »
Quote from: _nameless on May 09, 2024, 09:46:55 AM
Easiest solution would be to redrill the flex plate for the correct offset
That is how is now made on car. But it is really on strange place, aluminum there is too thin
I need to weld also not only drill hole

Quote from: kacperoooni on May 08, 2024, 03:40:14 AM
You need to find in IDA constant GDWRT
thank you, I will try to find it
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 22, 2024, 03:09:48 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 17 queries. (Pretty URLs adds 0s, 0q)