vcom
Newbie
Karma: +0/-0
 Offline
Posts: 2
|
 |
« on: July 27, 2012, 01:41:04 AM »
|
|
|
Hi Guys does anyone of you have some experience using Nefmoto with Porsche 996 Turbo Series? They have Bosch ME7.8 Kind regards from switzerland  Ray |
|
|
|
|
Logged
|
|
|
|
NOTORIOUS VR
Administrator
Hero Member
Karma: +58/-7
Offline
Posts: 1056
|
|
« Reply #1 on: July 31, 2012, 09:50:12 AM »
|
|
|
I'm trying to play with one currently and having a crappy time with it... No matter what file I seem to pull from the ECU it's garbage... no maps to be found.
Using MPPS V12, it seems like the 35kb file (data only) contains nothing, and when I attempt a boot mode read I only get 266kb file and again just garbage.
|
|
|
|
|
Logged
|
|
|
|
GTO
Newbie
Karma: +0/-0
Offline
Posts: 5
|
|
« Reply #2 on: August 05, 2012, 05:04:02 AM »
|
|
|
i do few, best way is desolder, boot mode work too with BS
|
|
|
|
|
Logged
|
|
|
|
lulu2003
Full Member
Karma: +11/-1
Offline
Posts: 242
|
|
« Reply #3 on: August 20, 2012, 08:14:48 AM »
|
|
|
Using MPPS V12, it seems like the 35kb file (data only) contains nothing, and when I attempt a boot mode read I only get 266kb file and again just garbage.
that car was already modded, right? used clone? -> PN |
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #4 on: August 21, 2012, 04:47:09 AM »
|
|
|
Try Galletto in boot mode?
I know there are a few people on this forum, who swear that MPPS reads in boot mode, but I never ever got it to work.
All it ever did was say mode not supported and asked me to reset the ECU. Then continued to read in normal mode on bench.
|
|
|
|
|
Logged
|
|
|
|
lulu2003
Full Member
Karma: +11/-1
Offline
Posts: 242
|
|
« Reply #5 on: August 21, 2012, 07:40:11 AM »
|
|
|
isn't ME7 bench=boot?  |
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #6 on: August 21, 2012, 07:56:37 AM »
|
|
|
isn't ME7 bench=boot? No! |
|
|
|
|
Logged
|
|
|
|
NOTORIOUS VR
Administrator
Hero Member
Karma: +58/-7
Offline
Posts: 1056
|
|
« Reply #7 on: August 21, 2012, 01:34:42 PM »
|
|
|
just to update... the issue was because the car was already tuned.. so MPPS encrypts the output due to a NOREAD in the file.
I solved it by using Galletto in boot mode and got the 1MB flash out successfully.
And actually I finished my first revision for his car from a stock 996T BIN... gonna see how that goes on later today, pretty pumped. I just hope the ORI I found on here was good (never know with internet files).
|
|
|
|
|
Logged
|
|
|
|
lulu2003
Full Member
Karma: +11/-1
Offline
Posts: 242
|
|
« Reply #8 on: August 22, 2012, 02:35:41 AM »
|
|
|
No!
but why put on bench, when not boot mode? |
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #9 on: August 22, 2012, 03:03:02 AM »
|
|
|
but why put on bench, when not boot mode? There are many reasons, one of them is that the dash interfers in some applications. That's not my point. My point is MPPS can't do boot mode, period. It can flash on bench by bypassing immo, but it does not do boot mode. |
|
|
|
|
Logged
|
|
|
|
lulu2003
Full Member
Karma: +11/-1
Offline
Posts: 242
|
|
« Reply #10 on: August 22, 2012, 03:55:01 AM »
|
|
|
of course MPPS does boot mode, but I think it depends alot on which SW+HW version, original or clone, ECU, harness etc.
|
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #11 on: August 22, 2012, 03:57:24 AM »
|
|
|
of course MPPS does boot mode, but I think it depends alot on which SW+HW version, original or clone, ECU, harness etc.
I want to see that for myself. Tried with 3 or 4 different ECU's so far. It can flash them on bench over KWP2000 by bypassing immo, but not a single one works in boot mode. If you set the ECU in boot mode it just tells you "mode not supported" and restart ECU. If you restart it with boot mode, it says that again. If you restart without boot mode only then it flashes. Any time you ground Pin 24 it does absolutely nothing. Just because you say it does, does not make it true  |
|
|
|
|
Logged
|
|
|
|
|
|
|
prj
|
|
« Reply #13 on: August 22, 2012, 06:05:35 AM »
|
|
|
I've used MPPS in bootmode before... works just fine  So you plug in the ecu, hold pin 24 to ground, and after that hit write? Because that's what I've done, and I've never got it to work on any ME7.1 or ME7.5 ECU. Galletto has never let me down in those cases |
|
|
|
|
Logged
|
|
|
|
NOTORIOUS VR
Administrator
Hero Member
Karma: +58/-7
Offline
Posts: 1056
|
|
« Reply #14 on: August 22, 2012, 06:08:53 AM »
|
|
|
Did you choose the boot mode version of the ECU in the list?
Also there is a Generic menu option for Bosch ECU's and that is 100% boot mode if you need it.
|
|
|
|
|
Logged
|
|
|
|
|
