Quen0tt0in
Newbie
Karma: +0/-0
 Offline
Posts: 11
|
 |
« on: November 14, 2024, 04:31:51 AM »
|
|
|
Hi everyone, i've been trying to flash read my ecu (ME7.5) and it keep giving me the same messages;
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Reading ECU flash memory failed.
Does anyone already had this problem ? or does anyone knows how to resolv it ?
Thanks everyone
|
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #1 on: November 14, 2024, 05:26:34 AM »
|
|
|
Buy MPPS or use galeto1260 software
|
|
|
|
|
Logged
|
|
|
|
davidklmn
Newbie
Karma: +2/-0
Offline
Posts: 3
|
|
« Reply #2 on: November 14, 2024, 01:14:07 PM »
|
|
|
I have the same problem every time i try to flash...
Here's what I do to fix it:
- Wait for error...
- When error occurs, disconnect from ECU
- After that reconnect and try to flash again.
That mostly helps for me.
My Car:
Audi A4 B7 1.8T Quattro Avant, ME7.5 with BFB Block
|
|
|
|
|
Logged
|
|
|
|
Quen0tt0in
Newbie
Karma: +0/-0
Offline
Posts: 11
|
|
« Reply #3 on: November 15, 2024, 04:04:18 AM »
|
|
|
Hi everyone,
So i've managed to start flash reading the Ecu properly.
the issue is that it take a very long time (i waited about 20 min without any signs on nefmoto software execept the last commande line that says "reading flash Ecu"), i manually cancelled it cause i didn't had the time to let it rest the entire day.
My question is how much time does it usually take to make the full read flash ?
|
|
|
|
|
Logged
|
|
|
|
JeanAwt
Full Member
Karma: +10/-12
Offline
Posts: 241
|
|
« Reply #4 on: November 17, 2024, 10:53:53 PM »
|
|
|
what cable did you use? what nefmoto settings? I read or write in 5 minutes. if you stop reading or writing you run the risk of not having the entire file
|
|
|
|
|
Logged
|
A4 B5 avant 1.8T 2000 NO QUATTRO
|
|
|
Quen0tt0in
Newbie
Karma: +0/-0
Offline
Posts: 11
|
|
« Reply #5 on: November 18, 2024, 12:13:57 AM »
|
|
|
I use a Chinese version of ross tech hex , Connect in slow int 38k baud. Some dude on the forum said that a higher baud rate could help get the file faster.
Envoyé de mon iPhone en utilisant Tapatalk
|
|
|
|
|
Logged
|
|
|
|
JeanAwt
Full Member
Karma: +10/-12
Offline
Posts: 241
|
|
« Reply #6 on: November 18, 2024, 01:56:05 AM »
|
|
|
yes try 58k
|
|
|
|
|
Logged
|
A4 B5 avant 1.8T 2000 NO QUATTRO
|
|
|
Quen0tt0in
Newbie
Karma: +0/-0
Offline
Posts: 11
|
|
« Reply #7 on: November 18, 2024, 02:26:08 AM »
|
|
|
Okay I’ll try that tomorrow thank man !
Envoyé de mon iPhone en utilisant Tapatalk
|
|
|
|
|
Logged
|
|
|
|
JeanAwt
Full Member
Karma: +10/-12
Offline
Posts: 241
|
|
« Reply #8 on: November 18, 2024, 05:00:19 AM »
|
|
|
52k slow init I just did it 4min
|
|
|
|
|
Logged
|
A4 B5 avant 1.8T 2000 NO QUATTRO
|
|
|
Quen0tt0in
Newbie
Karma: +0/-0
Offline
Posts: 11
|
|
« Reply #9 on: Yesterday at 05:52:49 AM »
|
|
|
Can you copy what is written in the dialog box so I can see what I should get ?
|
|
|
|
|
Logged
|
|
|
|
Quen0tt0in
Newbie
Karma: +0/-0
Offline
Posts: 11
|
|
« Reply #10 on: Yesterday at 05:54:33 AM »
|
|
|
Cause when I’m starting the read it just tells me reading écu flash memory and it is stuck on it.
I’ve tried a few times and waited around 10 min on a 58k baud set up.
Envoyé de mon iPhone en utilisant Tapatalk
|
|
|
|
|
Logged
|
|
|
|
|
