Me 7 - Application with INCA and ETK7

Pages: [1]

« previous next »

Author

Topic: Me 7 - Application with INCA and ETK7 - need Help! (Read 15803 times)

gregsback

Full Member

Karma: +0/-0
Offline

Offline

Posts: 50

	Me 7 - Application with INCA and ETK7 - need Help! « on: September 14, 2012, 10:43:09 AM »

Dear all,
does anybody use the ETK7 plus INCA for application?
If so I, I have some questions regarding the HW connection on the ECU board.

br
Greg


	Logged

IamwhoIam

Hero Member

Karma: +52/-114
Offline

Offline

Posts: 1070

	Re: Me 7 - Application with INCA and ETK7 - need Help! « Reply #1 on: September 15, 2012, 01:20:13 AM »

What do you need to know exactly?


	Logged

I have no logs because I have a boost gauge (makes things easier)

gregsback

Full Member

Karma: +0/-0
Offline

Offline

Posts: 50

	Re: Me 7 - Application with INCA and ETK7 - need Help! « Reply #2 on: September 15, 2012, 01:35:15 AM »

I would like to know the pin assignment between the 44pin pads (on the ECU Board) and the ERNI connector from the flat wire to the small connector board wetween the ETK and the ECU board.
Finally I'm not sure if this small board is really required for the ME7 ECUs or if it's only for EDC15 ECUs.
Can you help me? Or do you have a photo of such a setup?
BR
Greg


	Logged

zzambucca

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Re: Me 7 - Application with INCA and ETK7 - need Help! « Reply #3 on: November 06, 2012, 08:38:45 PM »

What hardware are you using to flash the ETK? ES590 or older hardware? Is it a ETK7, or ETK7.1? What version INCA are you running?


	Logged

gregsback

Full Member

Karma: +0/-0
Offline

Offline

Posts: 50

	Re: Me 7 - Application with INCA and ETK7 - need Help! « Reply #4 on: November 07, 2012, 08:29:21 AM »

Hi,
ES690 + ETK7 + INCA 5.4
Do you know anything about the setup?


	Logged

zzambucca

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Re: Me 7 - Application with INCA and ETK7 - need Help! « Reply #5 on: November 07, 2012, 04:29:05 PM »

I have a similar setup I am trying to get working. ETK7 on a ME7.1 ECM\ES590\INCA 6.2. I have a pdf of the manual for the ETK if that helps with the HW connection question you had. I can open my ECM and take a couple pictures if that helps also.


	Logged

gregsback

Full Member

Karma: +0/-0
Offline

Offline

Posts: 50

	Re: Me 7 - Application with INCA and ETK7 - need Help! « Reply #6 on: November 08, 2012, 12:05:06 AM »

Hi,
yes, the manual would be fine, and I would really be happy about a photo. I could get some ETAS description about the pinning, but so far I did not get the system running. Is this a "self made setup" or is this a development ECU?
You write "trying to get working", that means so far it does not work? What A2l/hex do you use? What ETK / Vehicle is it by the way? ;-)

many thanks in advance
Greg


	Logged

Nothery1952

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Re: Me 7 - Application with INCA and ETK7 - need Help! « Reply #7 on: October 11, 2018, 11:19:57 PM »

Sorry, for reactivating this old thread. Does anyone of you has a ProF configuration for the ME7.x (VW seed)? I´m looking for a ETK7 or ETK7.1 1.8T ECU. I found a shop years ago but I forgot to save the address. Can someone please give me a hint?

By the way for the record:
ETK 7.0: INCA version <= 7.0.x supported
ETK 7.1: all versions supported


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 23, 2024, 04:44:29 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search