NefMoto > Technical > Flashing and Chipping > Galetto kkl
Pages: [1]
« previous next »
Author Topic: Galetto kkl  (Read 12161 times)
Rsibiza
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 15
« on: December 26, 2010, 11:14:38 AM »
 China clone if you have KKL with L9637D or some SIXXXX OBD chip in KKL. Reason is to China clones have very bad output stage as imitation of OBD chip with LM339 or some
« Last Edit: March 10, 2011, 01:01:59 AM by Rsibiza » Logged
kls
Full Member
***

Karma: +12/-0
Offline Offline

Posts: 97
« Reply #1 on: December 26, 2010, 08:21:06 PM »
Thanks for posting this, I always like to have schematics on hand.
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3
« Reply #2 on: December 29, 2010, 07:41:17 PM »
This is why I like hosting this forum, because people I have never heard of before show up and post cool stuff like this.  Grin
Logged
Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
Rsibiza
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 15
« Reply #3 on: December 30, 2010, 01:11:15 AM »
Was not sure if it were apreciated,but tryed it.

Keep up the good work;)

Best regards.
Logged
DJGonzo
Guest
« Reply #4 on: January 07, 2011, 10:36:37 PM »
Thanks! I will try this out tomorrow.
Logged
elRey
Hero Member
*****

Karma: +32/-1
Offline Offline

Posts: 565
« Reply #5 on: January 08, 2011, 11:54:02 PM »
Does any of this help with 'Error changing speed' situations?
Logged
Rsibiza
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 15
« Reply #6 on: January 09, 2011, 04:28:09 AM »
This speed changing error did never appear to me...

Give a try on it,and u will see...
Logged
kls
Full Member
***

Karma: +12/-0
Offline Offline

Posts: 97
« Reply #7 on: January 09, 2011, 12:49:42 PM »
I have seen the "error changing speeds" error with certain ME7.1.1 builds(newer then 2003).

The error really had nothing to do with changing speeds and was simply the immobilizer not allowing the read while the ECU was on the bench. The solution was to put the ECU in the car and match it to the cluster or read/edit/write the eeprom and bypass the immobilizer.
Logged
elRey
Hero Member
*****

Karma: +32/-1
Offline Offline

Posts: 565
« Reply #8 on: January 19, 2011, 12:27:23 PM »
Quote from: kls on January 09, 2011, 12:49:42 PM
I have seen the "error changing speeds" error with certain ME7.1.1 builds(newer then 2003).

The error really had nothing to do with changing speeds and was simply the immobilizer not allowing the read while the ECU was on the bench. The solution was to put the ECU in the car and match it to the cluster or read/edit/write the eeprom and bypass the immobilizer.

I have had 3 or 4 situations where I got the changing speed error on stock ECUs in the car it came with (matched to), but I could read/write on the bench in boot mode. 2001, 2002, and a 2003.
Logged
tobz
Full Member
***

Karma: +3/-1
Offline Offline

Posts: 60
« Reply #9 on: January 24, 2011, 08:34:29 PM »
Soldering in these components can be a lil bit of a challenge. The legs on the FTDI chip are pretty small. :p
Logged
gsxeclipsepsi
Full Member
***

Karma: +0/-43
Offline Offline

Posts: 70
« Reply #10 on: August 21, 2012, 08:21:32 PM »
Hey, there is no picture or anything for the HOW TO so if someone could post it that would be great. Also how do you get ecu into boot mode while in the car?

Thanks
Kendel
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #11 on: August 21, 2012, 11:48:16 PM »
Quote from: gsxeclipsepsi on August 21, 2012, 08:21:32 PM
Hey, there is no picture or anything for the HOW TO so if someone could post it that would be great.

Did you search the s4 wiki for bootmode?

Quote
Also how do you get ecu into boot mode while in the car?

You can't easily. I have an ECU with a switch mounted to the case that i can barely reach while turning the ignition on.

Get a bench flashing setup, or buy a spare ecu.
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
NOTORIOUS VR
Administrator
Hero Member
*****

Karma: +58/-7
Offline Offline

Posts: 1056
« Reply #12 on: August 22, 2012, 06:10:52 AM »
Quote from: nyet on August 21, 2012, 11:48:16 PM
I have an ECU with a switch mounted to the case that i can barely reach while turning the ignition on.

Did the same... saved my ass a few times... I brought the switch to be behind the fuse box cover... so I just had to pop it off, press the switch while turning on the ign and voila boot mode. 
Logged
SCHNELL ENGINEERING BLOG ·  STANDALONE ECUS · TUNING · DYNO · WIRING · PARTS · VEMS
Google Talk: NOTORIOUS.VR
n00bs start here: http://s4wiki.com/wiki/Tuning
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 23, 2024, 09:40:34 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.022 seconds with 16 queries. (Pretty URLs adds 0s, 0q)