Pages: [1]
Author Topic: ME7.1/7.5 immo-off bin  (Read 20364 times)
ddillenger
Moderator
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« on: February 25, 2013, 09:30:01 PM »

I have used this on many ecu's with no issues. Make sure to use the 7.1.1 file if you don't have an me7.1/7.5 ecu.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
aRd
Newbie
*

Karma: +1/-1
Offline Offline

Posts: 13


« Reply #1 on: February 26, 2014, 11:10:58 PM »

Thank you for sharing
Logged
userpike
Hero Member
*****

Karma: +22/-1
Offline Offline

Posts: 763


« Reply #2 on: March 16, 2014, 09:06:46 AM »

I flashed this immo off .bin and got rid of the "immo not authenticated" error msg in Nef but I still get that the ECU has rejected security access and it won't let me go through with the reading or writing. What am I missing here?

This is for an HSbox that looks as if it had an LP file flashed to it from the dealer. I heard they do this now because the HS software has been superseded. I don't see how this should matter though.
Logged
c11rgd
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #3 on: May 26, 2014, 02:54:45 PM »

I have used this on many ecu's with no issues. Make sure to use the 7.1.1 file if you don't have an me7.1/7.5 ecu.

so can i use this to immo off the following ecu.

TT 225HP APX 8N0906018AE ME7.5 0261207030

as im using the engine in a mk1 golf conversion.
Logged
Bi-turbo
Full Member
***

Karma: +1/-7
Offline Offline

Posts: 164


« Reply #4 on: September 10, 2014, 01:30:08 AM »

Just to confirm.

Would i flash this bin as normal (bootmode + galletto)

If i then flash a file onto the car will it not put the immo back on if that bin file hasnt had immo off???
Logged
Bi-turbo
Full Member
***

Karma: +1/-7
Offline Offline

Posts: 164


« Reply #5 on: September 10, 2014, 01:35:39 AM »

Ignore the above...

I would use the 95040 program to flash the immo bin to the ecu which is different to the eprom if im correct?
Logged
turboat
Hero Member
*****

Karma: +44/-3
Offline Offline

Posts: 619


« Reply #6 on: September 10, 2014, 03:49:02 AM »

The convention on this site is:
- Flash - where the maps go (512kb or 1024kb)
- eeprom - where the immo data goes (512 or 1024bytes - i.e. 1024x smaller than the flash).

The immo bin on this page is for the eeprom, which is different from the flash where the maps are stored. You are correct, that you should use argdub's me7_95040 tool to write the eeprom.

However, I would always read the eeprom contents from the ecu, modify it for immo-off, and then write it back, rather than writing a generic immo-off.
Logged
Bi-turbo
Full Member
***

Karma: +1/-7
Offline Offline

Posts: 164


« Reply #7 on: September 10, 2014, 04:20:05 AM »

Thanks for the clarificaion

Ive looked at the immo bin in hex editor, is the immo at the same address in all ME7.1/7.5?

Could like you said just edit the hex with what is in the immob bin? if that makes sense

Thanks in advance
Logged
turboat
Hero Member
*****

Karma: +44/-3
Offline Offline

Posts: 619


« Reply #8 on: September 10, 2014, 05:30:33 AM »

7.1 and 7.5 seem to be the same, 7.1.1 is slightly different.

I usually use my tool to do immo off, because I can never remember how to set the checksum properly, but its super easy with a hex editor too. http://nefariousmotorsports.com/forum/index.php?topic=6134.15

As I did to a spare ecu this morning:

1. Read from ECU. (me7_95040 --OBD -r -p 1 eeprom.bin)

2. view info (eepromtool --in eeprom.bin)

3. turn off immo (eepromtool --in eeprom.bin --out eeprom_off.bin --immo off)

4. write back to ecu in boot mode (me7_95040 --bootmode -w -p 1 eeprom_off.bin)

took about 10 minutes. If you get a complaint about a checksum error on a virgin eeprom that you've just read from a virgin/working ecu, please post up on the thread for the tool.
« Last Edit: September 10, 2014, 05:48:24 AM by turboat » Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 19 queries. (Pretty URLs adds 0.001s, 0q)