everydayparadise
Full Member
Karma: +3/-0
 Offline
Posts: 81
|
 |
« Reply #45 on: August 26, 2014, 09:23:12 PM »
|
|
|
I wanted to give a quick update. I have read my car and have validated that the read was good. I used the EOBD1300.exe to do this. I have made the changes to the file, and now I'm trying to write them to the TCU, but I can't seem to get EOBD1300.exe to write a file to the TCU. I can read the binary file no problem and can identify the DSG, but that's it.
Any suggestions?
|
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #46 on: August 26, 2014, 09:30:25 PM »
|
|
|
suggestion: buy a real tool. are you going to be excited when you brick your dsg controller? probably not.
|
|
|
|
|
Logged
|
|
|
|
everydayparadise
Full Member
Karma: +3/-0
Offline
Posts: 81
|
|
« Reply #47 on: August 26, 2014, 09:55:48 PM »
|
|
|
suggestion: buy a real tool. are you going to be excited when you brick your dsg controller? probably not.
No I wouldn't be happy at all  ... Your totally right. I'm looking into getting SPI-Wizard III or byteshooter. but in the mean time I'm trying to see if I can test my files till I get them. |
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #48 on: August 26, 2014, 11:37:38 PM »
|
|
|
time to buy the mini dsg reader from china |
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #49 on: August 27, 2014, 06:14:05 AM »
|
|
|
and spare mechatronic  |
|
|
|
|
Logged
|
|
|
|
everydayparadise
Full Member
Karma: +3/-0
Offline
Posts: 81
|
|
« Reply #50 on: August 27, 2014, 08:33:10 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #51 on: August 27, 2014, 10:32:13 AM »
|
|
|
it seems you understand the whole process of DSG tuning by chinese tool  |
|
|
|
|
Logged
|
|
|
|
everydayparadise
Full Member
Karma: +3/-0
Offline
Posts: 81
|
|
« Reply #52 on: October 13, 2014, 10:23:30 AM »
|
|
|
Finally getting back on trying to flash my DSG. Does anyone know if you can use VC-Pro to flash BIN files to the DQ250 or the DQ200 http://www.vag-tech.eu/ |
|
|
|
|
Logged
|
|
|
|
Volsssy
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #53 on: August 30, 2015, 04:48:54 AM »
|
|
|
Yes, many times.
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #54 on: February 21, 2016, 06:33:04 AM »
|
|
|
Is this really able to write BIN? Think its only SGO
|
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #55 on: April 26, 2016, 06:40:50 PM »
|
|
|
Ok So I posted the file that I read with my own cable for the DQ250. So here it is.
Parts (All of them I got on ebay)
Transmission Connector Pigtail - The part number for the connector is 1J0 927 320 and then you just need to wires that fit. The best way to get the wires it to get a pig tail from a VW round transmission pigtail. There are not a lot of them out there but if you look hard enough you'll find them
12-Volt Lighter to Alligator Clips - I cut off the lighter and just used the Alligator Clips
OBD2 100cm 16Pin Male to Female Extension Cable - Just cut the male end off (ouch!)
FT232RL-Chip OBD2 Cable -
Software
EOBD1300.exe (See previous post for the exe)
After that I used these images and wired up the cable.
Friend sorry to ask, but how do you take out pins from donor VW round transmission pigtail? |
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #56 on: April 27, 2016, 07:53:56 AM »
|
|
|
 Maybe I found the answer to my doubt..... |
|
|
|
|
Logged
|
|
|
|
|
|
Wanka7a
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #58 on: May 17, 2020, 04:34:55 AM »
|
|
|
Did someone succeed to WRITE flash with this software EOBD1300.EXE?
I know .. "buy a real tool" or "buy a spare mechatronics" but I am looking for information about exactly this software. It identifies tcu ,reads flash ,no problem but when I press WRITE FLASH it does nothing. Just says Programming flash... and thats it. Doesn't even give me a chance to select a flash to write. I think maybe there is some trick to get it work at least to select a flash even if it doesn't get to write it in the tcu. If someone have any idea would be great. Thanks
|
|
|
|
|
Logged
|
|
|
|
|
