Pages: 1 [2] 3
Author Topic: rl > (rlmax_w, rlmx_w and rlsol_w)  (Read 17181 times)
prj
Hero Member
*****

Karma: +903/-420
Offline Offline

Posts: 5787


« Reply #15 on: May 17, 2013, 02:25:45 PM »

Desired load is used for the filling adjuster (FUEDK).
Logged

PM's will not be answered, so don't even try.
Log your car properly.
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Online Online

Posts: 12232


WWW
« Reply #16 on: May 17, 2013, 02:40:08 PM »

Thanks, now I see... Btw PID is completely stock as is turbo (K03). Yet I can't understant why wastegate DC isn't at 95 whenever I press gas pedal 100% and load haven't reached the target?

the PID driven by lde (ld error) not load deviation. Please review the FR :/

"ld" is NOT load....
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
phila_dot
Hero Member
*****

Karma: +170/-11
Offline Offline

Posts: 1709


« Reply #17 on: May 17, 2013, 02:51:38 PM »

Desired load is used for the filling adjuster (FUEDK).

I can never tell whether your disagreeing or not, but exactly.

Charge control or filling adjuster (FUEDK) as part of load realization (FE).

Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Online Online

Posts: 12232


WWW
« Reply #18 on: May 17, 2013, 02:58:47 PM »

Desired load is used for the filling adjuster (FUEDK).

but actual/desired load deviation does not drive LDRPID :/
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
phila_dot
Hero Member
*****

Karma: +170/-11
Offline Offline

Posts: 1709


« Reply #19 on: May 17, 2013, 03:16:20 PM »

I should correct my previous statement.

rlsol is evaluated against rl, but only for calculating throttle angle.
Logged
masterj
Hero Member
*****

Karma: +61/-5
Offline Offline

Posts: 1049



WWW
« Reply #20 on: May 17, 2013, 03:40:52 PM »

Um, guys, so KFLDRL is there to configure how much wgdc ecu can use on each pid correction? Ie: If duty cycle from PID returns as 10% KDLDRL maps it to whatever RPM/10% cell is? In my case it would be  38% @ 4000 RPM? Right? So basically this maps allows us to configure how fast PID will get to the target pressure? As in step size of corrections?

If we set this whole map to 95% then even smallest wgdc requested from pid will result in 95% and thus fastest achievement of target charge but also sinusoidal PID? Or am I completely wrong on this?
Logged

nyet
Administrator
Hero Member
*****

Karma: +604/-166
Online Online

Posts: 12232


WWW
« Reply #21 on: May 17, 2013, 06:01:23 PM »

Um, guys, so KFLDRL is there to configure how much wgdc ecu can use on each pid correction? Ie: If duty cycle from PID returns as 10% KDLDRL maps it to whatever RPM/10% cell is? In my case it would be  38% @ 4000 RPM? Right? So basically this maps allows us to configure how fast PID will get to the target pressure? As in step size of corrections?

If we set this whole map to 95% then even smallest wgdc requested from pid will result in 95% and thus fastest achievement of target charge but also sinusoidal PID? Or am I completely wrong on this?

If you aren't already at 95% during spool *even with a stock KFLDRL* you are doing it wrong.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
prj
Hero Member
*****

Karma: +903/-420
Offline Offline

Posts: 5787


« Reply #22 on: May 18, 2013, 02:02:15 AM »

I should correct my previous statement.

rlsol is evaluated against rl, but only for calculating throttle angle.

That is basically why I said what I said Smiley
Specifically because desired/actual does exist, since it subtracts rl from rlsol and that goes into throttle angle set point.
« Last Edit: May 18, 2013, 02:03:56 AM by prj » Logged

PM's will not be answered, so don't even try.
Log your car properly.
brs
Full Member
***

Karma: +3/-11
Offline Offline

Posts: 61


« Reply #23 on: September 13, 2019, 11:56:37 AM »

Hi all,
i know this is old topic but i didn't want open a new topic.
My issue,rlsow_w not ever following to rlmax_w and rlmx_w
rlmx_w seems 254 but  rlsol_w seems max ~220 in my logs.
is this a torque intervention? or something else ?
maybe my kp axis wrong (KFMIOP) , i don't know..
KFMIOP
@166DE x-axis@13074 and y-axis@16840 in my .kp

Log and ori attached
thanks in advance

Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #24 on: September 13, 2019, 12:22:18 PM »

Are you sure that your turbo can make more power? Where is WGDC?
Look at you KFMIRL values, they have smaler value than a LDRXN.
I must go, but tomorow i will explain better
Logged
brs
Full Member
***

Karma: +3/-11
Offline Offline

Posts: 61


« Reply #25 on: September 13, 2019, 12:31:07 PM »

Are you sure that your turbo can make more power? Where is WGDC?
Look at you KFMIRL values, they have smaler value than a LDRXN.
I must go, but tomorow i will explain better


Turbo is a gt28 with external wg.
checked repeatedly, KFMIRL values  they haven't smaler value than a LDRXN
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #26 on: September 13, 2019, 12:52:01 PM »

Turbo is a gt28 with external wg.
checked repeatedly, KFMIRL values  they haven't smaler value than a LDRXN

Post a pic of KFMIRL and LDRXN
Logged
brs
Full Member
***

Karma: +3/-11
Offline Offline

Posts: 61


« Reply #27 on: September 13, 2019, 12:59:16 PM »

Here
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #28 on: September 13, 2019, 03:39:58 PM »

LDRXN go to KFMIOP,  you get "misol"... "misol" go to KFMIRL and values you get after conversion are lover than a LDRXN values
So raise KFMIOP or KFMIRL values at "misol" you get from log

What about your KFLDHBN? Can you log it?
Logged
brs
Full Member
***

Karma: +3/-11
Offline Offline

Posts: 61


« Reply #29 on: September 13, 2019, 03:45:20 PM »

KFLDHBN @1EE7E and all FF
Logged
Pages: 1 [2] 3
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.043 seconds with 17 queries. (Pretty URLs adds 0s, 0q)