NefMoto > Technical > Flashing and Chipping > problems flashing my s4 stage 3
Pages: [1] 2
« previous next »
Author Topic: problems flashing my s4 stage 3  (Read 16622 times)
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« on: March 10, 2011, 02:12:43 PM »
i have a problem flashing my a-box ecu that already has m-box software from AWE.
im using cable FT232R
i can read ecu info and codes, i also saved a copy of the .bin file from my current tune.

but when i try to flash with normally it fails flashing one sector at a time. then i select erase entire memory and it tries but i get this message over and over in the log file.
8: USER: Truncated log file because it was larger than 10 megabytes.
10/Mar/2011 01:24:32.872: LOG: Received negative response for service ID: RequestRoutineResultsByLocalIdentifier, with response code: RoutineNotCompleteOrServiceInProgress
10/Mar/2011 01:24:32.874: LOG: Sent message with service ID RequestRoutineResultsByLocalIdentifier
10/Mar/2011 01:24:32.886: LOG: Received message with service ID NegativeResponse
10/Mar/2011 01:24:32.888: LOG: Received negative response for service ID: RequestRoutineResultsByLocalIdentifier, with response code: RoutineNotCompleteOrServiceInProgress
10/Mar/2011 01:24:32.889: LOG: Sent message with service ID RequestRoutineResultsByLocalIdentifier
10/Mar/2011 01:24:32.907: LOG: Received message with service ID NegativeResponse
10/Mar/2011 01:24:32.907: LOG: Received negative response for service ID: RequestRoutineResultsByLocalIdentifier, with response code: RoutineNotCompleteOrServiceInProgress
10/Mar/2011 01:24:32.909: LOG: Sent message with service ID

also here is my current awe ecu tune
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3
« Reply #1 on: March 10, 2011, 02:18:47 PM »
Can you post the full log file? If you go to the file menu in the flashing software you can find the log file.
Logged
Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
judeisnotobscure
Sr. Member
****

Karma: +38/-10
Offline Offline

Posts: 379
« Reply #2 on: March 10, 2011, 03:02:25 PM »
nothing to say about the flashing but take a look at
kvb, fuel consumption constant for display, looks low for a 630cc setup... is that because you are running a 3 bar fpr?

also looks like you could add some timing up top (higher rpms) if you wanted, in kfzw2
not sure what octane you run though. if it's 93 then definately, if it's 91 just a little.
« Last Edit: March 10, 2011, 04:09:51 PM by judeisnotobscure » Logged
I have a b5 s4
but i just want to dance.
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« Reply #3 on: March 10, 2011, 05:26:07 PM »
Quote from: Tony@NefMoto on March 10, 2011, 02:18:47 PM
Can you post the full log file? If you go to the file menu in the flashing software you can find the log file.

i am using a 3 bar fpr and i havent touched the kvb map except with vagcom which can only go so far.
Logged
phila_dot
Hero Member
*****

Karma: +173/-11
Offline Offline

Posts: 1709
« Reply #4 on: March 10, 2011, 05:30:06 PM »
Is it flashed or a socketed chip?
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3
« Reply #5 on: March 10, 2011, 05:31:39 PM »
The log was truncated because it was too long, so it doesn't show anything useful.

Do you know how far it got flashing the entire chip at once?

Can you try flashing again and save the log file before it overflows and gets truncated?
Logged
Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« Reply #6 on: March 10, 2011, 05:37:50 PM »
Quote from: Tony@NefMoto on March 10, 2011, 05:31:39 PM
The log was truncated because it was too long, so it doesn't show anything useful.

Do you know how far it got flashing the entire chip at once?

Can you try flashing again and save the log file before it overflows and gets truncated?
this is what it said..

Disabling Windows sleep mode.
Writing ECU flash memory.
Fast writing premium feature NOT enabled.
Reading ECU identification option: calibrationEquipmentSoftwareNumber
Read ECU identification option with unknown scaling record.
Successfully read ECU identification information
ECU reports programming session preconditions have been met.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Memory layout is valid.
Starting to flash data block.
Calculating flash checksum to determine if flashing is necessary for range: 0x00800000 to 0x00810000
Flash checksum does not match new data, flashing is necessary.
Requesting flash memory erase for address range 0x00800000 to 0x0080FFFF.
Erase flash memory routine did not start or complete correctly.
Skipping flash sector and continuing flashing process.
6% complete.
Starting to flash data block.
Calculating flash checksum to determine if flashing is necessary for range: 0x00810000 to 0x00820000
Flash checksum does not match new data, flashing is necessary.
Requesting flash memory erase for address range 0x00810000 to 0x0081FFFF.
Successfully erased flash memory.
Requesting download to ECU for address range 0x00810000 to 0x0081FFFF.
Request download to ECU succeeded.
Starting data transfer.
Data transfer failed.
100% complete.
Writing ECU flash memory failed.
Restoring Windows sleep mode.
Disconnecting because no response was received for the Tester Present message.
Disconnected

 i dont think it did anything be cause i just took my car to the store so the ecu is not bricked yet.lol
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3
« Reply #7 on: March 10, 2011, 08:22:36 PM »
Quote from: coreyj03 on March 10, 2011, 05:37:50 PM
Quote from: Tony@NefMoto on March 10, 2011, 05:31:39 PM
The log was truncated because it was too long, so it doesn't show anything useful.

Do you know how far it got flashing the entire chip at once?

Can you try flashing again and save the log file before it overflows and gets truncated?
this is what it said..

Disabling Windows sleep mode.
Writing ECU flash memory.
Fast writing premium feature NOT enabled.
Reading ECU identification option: calibrationEquipmentSoftwareNumber
Read ECU identification option with unknown scaling record.
Successfully read ECU identification information
ECU reports programming session preconditions have been met.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Memory layout is valid.
Starting to flash data block.
Calculating flash checksum to determine if flashing is necessary for range: 0x00800000 to 0x00810000
Flash checksum does not match new data, flashing is necessary.
Requesting flash memory erase for address range 0x00800000 to 0x0080FFFF.
Erase flash memory routine did not start or complete correctly.
Skipping flash sector and continuing flashing process.
6% complete.
Starting to flash data block.
Calculating flash checksum to determine if flashing is necessary for range: 0x00810000 to 0x00820000
Flash checksum does not match new data, flashing is necessary.
Requesting flash memory erase for address range 0x00810000 to 0x0081FFFF.
Successfully erased flash memory.
Requesting download to ECU for address range 0x00810000 to 0x0081FFFF.
Request download to ECU succeeded.
Starting data transfer.
Data transfer failed.
100% complete.
Writing ECU flash memory failed.
Restoring Windows sleep mode.
Disconnecting because no response was received for the Tester Present message.
Disconnected

 i dont think it did anything be cause i just took my car to the store so the ecu is not bricked yet.lol

Do you have the log file for that flashing attempt?
Logged
Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« Reply #8 on: March 13, 2011, 05:42:27 PM »
here is the log for a recent attempt.
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3
« Reply #9 on: March 14, 2011, 03:55:26 PM »
So this log shows that you skipped flashing the first sector, and then the second sector failed to write properly. Have you ever tried the "erase entire flash" option instead of skipping the sector?
Logged
Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« Reply #10 on: March 14, 2011, 04:13:03 PM »
Quote from: Tony@NefMoto on March 14, 2011, 03:55:26 PM
So this log shows that you skipped flashing the first sector, and then the second sector failed to write properly. Have you ever tried the "erase entire flash" option instead of skipping the sector?

i did the first time i tried but this is my only ecu and working car so i cant afford for it to mess up.

do you think my cable is bad? it wont read from vagcom anymore since i installed the nefmoto software and cmd driver.
Logged
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« Reply #11 on: March 17, 2011, 09:12:53 PM »
FOUND MY PROBLEM... Angry

This is y i cant flash a new file. anyone have a stock m or a box ecu?

i took the chip off the board being a curious dumbass and when i put the ecu back into my car i have fuel injector 1 open circuit  :'(  car ran on 5 cylinders all the way home from work. i must have fried something with static discharge i dont know if its the ecu or the injector which only has 3000 miles on it.
« Last Edit: March 17, 2011, 09:15:02 PM by coreyj03 » Logged
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« Reply #12 on: March 17, 2011, 09:35:00 PM »
on second thought i think i could have bent the top left pin slightly on the socketed chip so its not getting a good connection. i pulled the ecu back out and reseated the chip and it ran fine for 50 miles then started firing on only 5 cylinders again
« Last Edit: March 18, 2011, 05:29:52 PM by coreyj03 » Logged
phila_dot
Hero Member
*****

Karma: +173/-11
Offline Offline

Posts: 1709
« Reply #13 on: March 17, 2011, 09:54:13 PM »
That is why I asked at the beginning.
Logged
coreyj03
Full Member
***

Karma: +10/-5
Offline Offline

Posts: 173
« Reply #14 on: March 17, 2011, 11:50:42 PM »
I  have stock mbox ecu on the way to me now. hopefully soon then i can flash my car
« Last Edit: March 18, 2011, 05:27:41 PM by coreyj03 » Logged
Pages: [1] 2
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 23, 2024, 01:51:44 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.054 seconds with 17 queries. (Pretty URLs adds 0s, 0q)