Waspjr
Full Member
Karma: +0/-0
 Offline
Posts: 64
|
 |
« on: October 21, 2013, 09:08:42 PM »
|
|
|
I have a 2005 1.8t amb cvt i read the ecu file nef moto via a genuine rosstech cable in dumb mode i had to use 38400 baud and 29f800bb it read ok and then i went to start the car it didnt run i then replaced my file back onto the ecu and it still wouldnt run i got a improper decode DTC and the only way i can get it to run is if i turn ignition on and use vcds to clear the codes then it will run but only once
Any ideas ?
Thanks in advance
|
|
|
|
|
Logged
|
|
|
|
jackson.amrol@gmail.com
Full Member
Karma: +4/-6
Offline
Posts: 128
"you sir are an animal"
|
|
« Reply #1 on: October 21, 2013, 09:25:58 PM »
|
|
|
Deathcode? DTC16985? Post the specific DTC
Does it run as in you can drive it? or that it starts briefly and dies?
|
|
|
|
|
Logged
|
Lost, No.. My minds around here somewhere..
Shh, I'm calling my mom.. "It's 3AM" SHH!
Mom, is there such a thing as kosher pork?
"I'm not bailing you out tonight"...
|
|
|
Waspjr
Full Member
Karma: +0/-0
Offline
Posts: 64
|
|
« Reply #2 on: October 21, 2013, 09:28:41 PM »
|
|
|
When i clear the codes via nef p0112 shows up all the time then i can start the car but after i shut down i scan codes and get nothing. I then try to start and it wont start and gives me 3 codes p0597 unknown dtc. P0112 decoding not licensed. And p0602 decoding not licensed
Is this a sign i have triggered my immobilizer?
|
|
|
|
|
Logged
|
|
|
|
Waspjr
Full Member
Karma: +0/-0
Offline
Posts: 64
|
|
« Reply #3 on: October 21, 2013, 09:30:00 PM »
|
|
|
Car runs and drives normal i can hear fuel pump i am assuming its cutting my ignition
|
|
|
|
|
Logged
|
|
|
|
Waspjr
Full Member
Karma: +0/-0
Offline
Posts: 64
|
|
« Reply #4 on: October 21, 2013, 09:41:48 PM »
|
|
|
I have checked my dtc logs and i have just done a engine swap and the po597 and p0112 were their prior to the read my bad sorry for mis informing but the p0602 is not good control module programming error  |
|
|
|
|
Logged
|
|
|
|
jackson.amrol@gmail.com
Full Member
Karma: +4/-6
Offline
Posts: 128
"you sir are an animal"
|
|
« Reply #5 on: October 21, 2013, 09:47:06 PM »
|
|
|
Use me7_check to check your .bin for bad checksums, if so you'll have to clear the DTC in the eeprom and write it back.. Did you make a backup of your eeprom?
|
|
|
|
|
Logged
|
Lost, No.. My minds around here somewhere..
Shh, I'm calling my mom.. "It's 3AM" SHH!
Mom, is there such a thing as kosher pork?
"I'm not bailing you out tonight"...
|
|
|
|
ddillenger
|
|
« Reply #6 on: October 21, 2013, 09:50:04 PM »
|
|
|
This happens on the later ME7.5 sometimes. Write your file back, then disconnect, turn the key OFF for 10 seconds, then ON for 30 seconds without starting. Should be good to go after that.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
Waspjr
Full Member
Karma: +0/-0
Offline
Posts: 64
|
|
« Reply #7 on: October 21, 2013, 10:12:50 PM »
|
|
|
Ddillenger you are awesome!! i could kiss you right now lol worked like a charm thanks for the help i was really hateing on myself for trying this out but the wicked ppl of nef had pulled threw thanks jackson take it easy
Cheers
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #8 on: October 21, 2013, 10:27:04 PM »
|
|
|
No worries man, glad you got it sorted.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
A4Rich
Full Member
Karma: +10/-0
Offline
Posts: 116
|
|
« Reply #9 on: January 06, 2014, 07:45:40 AM »
|
|
|
Hi I have a similar problem with my 2004 1.8T AMB. I read the ecu file ok via nefmoto (genuine rosstech cable in dumb mode, 10400 baud and 29f800bb) and verified using me7_check. Afterwards though it would not start and I got P0602 and P0562 DTCs. I then cleared DTCs using nefmoto and flashed the original ecu file following Ddillenger's post above which was done successfully. But still didn't have any luck starting the car.
Any suggestions would be much appreciated, thanks.
|
|
|
|
« Last Edit: January 06, 2014, 07:56:56 AM by Braunbär »
|
Logged
|
|
|
|
|
littco
|
|
« Reply #10 on: January 06, 2014, 02:04:01 PM »
|
|
|
Hi I have a similar problem with my 2004 1.8T AMB. I read the ecu file ok via nefmoto (genuine rosstech cable in dumb mode, 10400 baud and 29f800bb) and verified using me7_check. Afterwards though it would not start and I got P0602 and P0562 DTCs. I then cleared DTCs using nefmoto and flashed the original ecu file following Ddillenger's post above which was done successfully. But still didn't have any luck starting the car.
Any suggestions would be much appreciated, thanks.
Pretty sure the EEPROM will need re flashing... Sometimes only way to resolve p0602 code is to reflash EEPROM.. Nefmoto seems to do this far to often ... |
|
|
|
|
Logged
|
|
|
|
A4Rich
Full Member
Karma: +10/-0
Offline
Posts: 116
|
|
« Reply #11 on: January 06, 2014, 02:17:26 PM »
|
|
|
Thanks littco.
I didn't backup my EEPROM before reading with nefmoto is it still possible to use ArgDub tool?
|
|
|
|
|
Logged
|
|
|
|
|
littco
|
|
« Reply #12 on: January 06, 2014, 03:07:14 PM »
|
|
|
Thanks littco.
I didn't backup my EEPROM before reading with nefmoto is it still possible to use ArgDub tool?
Yes, absolutely.. Either download a Virgin EEPROM and flash it on. Or Download your EEPROM, copy the immob hex and write that to the Virgin EEPROM and change checksum.. |
|
|
|
|
Logged
|
|
|
|
A4Rich
Full Member
Karma: +10/-0
Offline
Posts: 116
|
|
« Reply #13 on: January 07, 2014, 03:54:02 PM »
|
|
|
Thanks again, I have a lot to learn...
I verified the DTC codes again this time in VCDS, I had P1681 and no longer had P0602 or P0562. I was able to connect with the ECU and flash the ecu again this time successfully. Car is now running fine, no DTCs!
|
|
|
|
|
Logged
|
|
|
|
|
