Hi there! I know most of you guys don´t light newbies with new topics, but believe me, I can't make any progress for 2 weeks now, I read 99% of the connection problems topics here, and can't figure out what's going on.

Here's my log... tried 2 RT cables (from those I only got CANT READ TEST ECHO, VCDS worked fine, always dumb mode), then this Blue Ebay one with FT232R, I got a little further.

Tried deleting all drivers (set devmgr_show_nonpresent_devices=1 trick), installing generic ones, then most recent ones from WHQL (2.08.30), tried Nefmoto 1.8.something and 1.9.3.2... tried slow/fast init, latency 2ms, all bauds.

Well I get this:

05/nov/2013 01:30:32.906: LOG: Opened NefMoto VW Audi ME7 Flasher Logger 1.9.3.2
05/nov/2013 01:30:44.114: LOG: Setting Address: 0x01 KeyByte1: 0x6B KeyByte2: 0x0F
05/nov/2013 01:30:44.161: LOG: Opened FTDI device.
05/nov/2013 01:30:44.163: LOG: FTDI device info - Description: FT232R USB UART Serial Number: A9UL93RB Device Type: FT_DEVICE_232R ID: 0x4036001 Device Flags: 0x0
05/nov/2013 01:30:44.165: LOG: FTDI ChipID DLL is loaded, checking chip ID...
05/nov/2013 01:30:44.173: LOG: FTDI device chip ID: 0x3F28FEF9
05/nov/2013 01:30:44.229: USER: Validated FTDI device is in dumb mode.
05/nov/2013 01:30:44.244: LOG: Starting send receive thread.
05/nov/2013 01:30:44.264: LOG: Send receive thread now started.
05/nov/2013 01:30:44.270: USER: Disconnected
05/nov/2013 01:30:44.318: LOG: Setting communication timings to defaults.
05/nov/2013 01:30:44.322: LOG: Set timing parameters to defaults.
05/nov/2013 01:30:44.323: USER: Connecting...
05/nov/2013 01:30:44.337: LOG: Setting communication timings to defaults.
05/nov/2013 01:30:44.347: USER: Starting slow init connection.
05/nov/2013 01:30:46.949: USER: Connecting to address 0x01.
05/nov/2013 01:30:49.773: LOG: Failed to read sync byte, guessing baud rate is actually 9600.
05/nov/2013 01:30:49.815: LOG: Not enough key bytes, read: 0
05/nov/2013 01:30:49.823: USER: Slow init failed.
05/nov/2013 01:30:49.825: USER: Disconnected
05/nov/2013 01:30:49.842: LOG: Setting communication timings to defaults.
05/nov/2013 01:30:49.844: USER: Connecting...
05/nov/2013 01:30:49.866: LOG: Setting communication timings to defaults.
05/nov/2013 01:30:49.867: USER: Starting slow init connection.
05/nov/2013 01:30:52.470: USER: Connecting to address 0x01.
05/nov/2013 01:30:55.274: LOG: Failed to read sync byte, guessing baud rate is actually 9600.
05/nov/2013 01:30:55.316: LOG: Not enough key bytes, read: 0
05/nov/2013 01:30:55.325: USER: Slow init failed.
05/nov/2013 01:30:55.326: USER: Disconnected
05/nov/2013 01:30:55.345: LOG: Setting communication timings to defaults.
05/nov/2013 01:30:55.347: USER: Connecting...
05/nov/2013 01:30:55.371: LOG: Setting communication timings to defaults.
05/nov/2013 01:30:55.372: USER: Starting slow init connection.
05/nov/2013 01:30:57.974: USER: Connecting to address 0x01.
05/nov/2013 01:31:00.779: LOG: Failed to read sync byte, guessing baud rate is actually 9600.
05/nov/2013 01:31:00.820: LOG: Not enough key bytes, read: 0
05/nov/2013 01:31:00.830: USER: Slow init failed.
05/nov/2013 01:31:00.831: USER: Disconnected
05/nov/2013 01:31:00.888: LOG: Setting communication timings to defaults.
05/nov/2013 01:31:00.900: LOG: Closing FTDI device.
05/nov/2013 01:31:00.917: LOG: Send receive thread now terminated.

PC is W7, core i-5.

Thank you very much and I'm sorry if I missed something.