Pages: 1 [2]
Author Topic: ME7.5 skip pulse at startup  (Read 12470 times)
jtorres
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 36


« Reply #15 on: April 04, 2014, 11:34:28 PM »

Nyet, i donĀ“t want to inhibit just the spark at start up, that would cause the inyectors to flood the engine as you stated.

What i am looking is that the ECU kind of ignore the first pulses from the crank trigger so the engine crank turns but nothing happen: Neither spark nor inyection, until some time after.

That is a function of the megasquirt ecu, it is called skip pulse. Main function to build oil pressure.
Logged
jtorres
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 36


« Reply #16 on: April 04, 2014, 11:43:24 PM »

you could also just remove your fuel checkvalve Smiley

you can also install a starter button and crank it up without the ignition on, but that will be the lazy solution.


If an antilag system can be implemented why this not?
Logged
titi65
Jr. Member
**

Karma: +1/-0
Offline Offline

Posts: 43


« Reply #17 on: April 05, 2014, 12:10:48 AM »

Have you check my last reply ?
Logged
jtorres
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 36


« Reply #18 on: April 05, 2014, 12:14:55 AM »

Have you check my last reply ?


Yes!

 i can´t find kfztnwakl and tvnwakl at the ME7.1 FR but i will look at the damos.

For the cranking ignition timing: kfzwmnst totally is!


edit: i did look at the damos but kfztnwakl and tvnwakl are not there.


THX!
« Last Edit: April 05, 2014, 12:36:20 AM by jtorres » Logged
titi65
Jr. Member
**

Karma: +1/-0
Offline Offline

Posts: 43


« Reply #19 on: April 05, 2014, 12:41:54 AM »

You're welcome.
In ME7.4.6, theses datas exists, but I can't find on the documentation ME7.1.

Maybe on ME7.5 . . .
Logged
userpike
Hero Member
*****

Karma: +22/-1
Offline Offline

Posts: 763


« Reply #20 on: April 05, 2014, 07:55:24 AM »

I'm pretty sure IGNDELAY is not what you want.



pretty sure you are right. the best translation I could come up with said that it only delays the ignition only until the first full cylinder fill, so a max of 1 crankshaft rotation or 360 degrees but the min could be 0 degrees rotation.  I think it has this for emissions reasons.

I'm not so sure there is a "skip pulse" function in me7.5. I spent a good 2/3 hours looking for some evidence in the FR while referencing a ME7.5 fully defined definition file. I do remember seeing IGNDELAYCT somewhere but didn't get to it yet.
Logged
jtorres
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 36


« Reply #21 on: April 06, 2014, 01:54:03 AM »

You're welcome.
In ME7.4.6, theses datas exists, but I can't find on the documentation ME7.1.

Maybe on ME7.5 . . .

The damos i have is for a me7.5 and there is not such parameters named like that in there. Maybe they are named sligthly different.
Logged
Pages: 1 [2]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.022 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)