NefMoto > Technical > Cluster and Immobilizer (Moderator: ddillenger) > 8D0907557 immo off
Pages: 1 [2]
« previous next »
Author Topic: 8D0907557 immo off  (Read 20393 times)
eliotroyano
Hero Member
*****

Karma: +48/-9
Offline Offline

Posts: 826
« Reply #15 on: September 24, 2014, 04:44:04 AM »
I don't know M3.2 so much, but using same idea of M38x/M592 try this one.
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601
« Reply #16 on: May 12, 2016, 12:18:03 PM »
Hi,

is there a way to run this kind of ecu on the bench and check channel 91 for immo status like on the later M3.83?

I had a look at the wiring but there is no direct K-Line to the ecu. Only to the dash and immo box...

Quote
D6, D9, D10 - +12V
D11, D12, E11, E12 - ground
A7 -W wire.

Thats all i found but W-line is to the immo box.

maybe someone can help with this old stuff Smiley
Logged
eliotroyano
Hero Member
*****

Karma: +48/-9
Offline Offline

Posts: 826
« Reply #17 on: May 12, 2016, 12:35:44 PM »
Quote from: aef on May 12, 2016, 12:18:03 PM
Hi,
is there a way to run this kind of ecu on the bench and check channel 91 for immo status like on the later M3.83?
I had a look at the wiring but there is no direct K-Line to the ecu. Only to the dash and immo box...
Thats all i found but W-line is to the immo box.
maybe someone can help with this old stuff Smiley

Normally in this ECUs W-line connects to the Dash and then from Dash goes out K-Line to diagnostic port. Try doing diagnostic though W-line and comment it. If it does not work, maybe you can share complete ECU pinout to take a look.
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601
« Reply #18 on: May 12, 2016, 11:05:20 PM »
This is what i have
Logged
eliotroyano
Hero Member
*****

Karma: +48/-9
Offline Offline

Posts: 826
« Reply #19 on: May 13, 2016, 11:03:18 AM »
Quote from: aef on May 12, 2016, 12:18:03 PM
Hi,
is there a way to run this kind of ecu on the bench and check channel 91 for immo status like on the later M3.83?
I had a look at the wiring but there is no direct K-Line to the ecu. Only to the dash and immo box...
Thats all i found but W-line is to the immo box.
maybe someone can help with this old stuff Smiley

Did you test C12 pin --> J189 Auto-Check-System?
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601
« Reply #20 on: May 15, 2016, 06:35:44 AM »
A7 is K-line

Smiley worked
Logged
eliotroyano
Hero Member
*****

Karma: +48/-9
Offline Offline

Posts: 826
« Reply #21 on: May 15, 2016, 05:54:34 PM »
Quote from: aef on May 15, 2016, 06:35:44 AM
A7 is K-line
Smiley worked

Ok!!!!
Logged
Pages: 1 [2]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 30, 2024, 03:29:54 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)