bigdawg56
Newbie
Karma: +2/-0
 Offline
Posts: 10
|
 |
« on: May 18, 2011, 03:15:49 PM »
|
|
|
First of all i tried just to validate memory and all of this happenened. I found out that it had had a apr trial tune in the past. its a 2004 audi a6 s-line 4Z7907551AA
VCDS-Lite Version: Release 1.1
Wednesday, 18 May 2011, 17:10:05.
Chassis Type: 4B - Audi A6 C5
Scan: 01,02,03,06,08,15,16,17,18,34,35,36,37,45,55,56,57,65,67,75,76,77
-------------------------------------------------------------------------------
Address 01: Engine Labels: 078-907-551-AZA.LBL
Controller: 4Z7 907 551 AA
Component: 2.7L V6/5VT G 0010
Coding: 07752
Shop #: WSC 77875
VCID: 8277890B9D01
WAUCD64B34N096051 AUZ7Z0D2618165
3 Faults Found:
18089 - Control Module Programming Not Finished
P1681 - 35-00 - -
18011 - Shareware Version. To Decode all DTCs
P1603 - 35-10 - Please Register/Activate - Intermittent
18010 - Shareware Version. To Decode all DTCs
P1602 - 35-10 - Please Register/Activate - Intermittent
Readiness: 0110 1101
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 01V-927-156.LBL
Controller: 4B0 927 156 EE
Component: AG5 01V 2.7l5VT USA 2223
Coding: 01002
Shop #: WSC 02334
VCID: 6EAF4DBB3999
1 Fault Found:
18258 - Powertrain Data Bus: Missing Message from ECU
P1850 - 35-10 - - - Intermittent
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 4B0-614-517.LBL
Controller: 4B0 614 517 H
Component: ABS/ESP allrad 3428
Coding: 06397
Shop #: WSC 02334
VCID: 263F759BD1E9
2 Faults Found:
18258 - Powertrain Data Bus: Missing Message from ECU
P1850 - 35-10 - - - Intermittent
18258 - Shareware Version. To Decode all DTCs
P1850 - 35-10 - Please Register/Activate - Intermittent
|
|
|
|
|
Logged
|
|
|
|
|
DJGonzo
Guest
|
|
« Reply #1 on: May 18, 2011, 03:17:25 PM »
|
|
|
Seems weird. You get no spark/fuel?
|
|
|
|
|
Logged
|
|
|
|
Jason
Hero Member
Karma: +38/-0
Offline
Posts: 500
Breaks everything!
|
|
« Reply #2 on: May 18, 2011, 05:03:02 PM »
|
|
|
Are you able to read the flash using the NefMoto flasher?
|
|
|
|
|
Logged
|
|
|
|
|
|
bigdawg56
Newbie
Karma: +2/-0
Offline
Posts: 10
|
|
« Reply #4 on: May 19, 2011, 02:13:45 AM »
|
|
|
no i'm not able to read the flash. it seems as though im locked out.
|
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #5 on: May 19, 2011, 03:35:56 PM »
|
|
|
Can you post the log file from the NefMoto flasher?
Validating the memory layout only tries to read the ECU flash, it does modify the flash at all.
One thing you can try, is to connect to the ECU with NefMoto flasher, and then disconnect. That will hopefully cause the ECU to think that "programming" has finished.
|
|
|
|
|
Logged
|
|
|
|
bigdawg56
Newbie
Karma: +2/-0
Offline
Posts: 10
|
|
« Reply #6 on: May 21, 2011, 02:41:58 AM »
|
|
|
tried to connect and reconnect nothing happened. The log file is attached
|
|
|
|
|
Logged
|
|
|
|
|
gremlin
|
|
« Reply #7 on: May 21, 2011, 11:07:38 AM »
|
|
|
tried to connect and reconnect nothing happened. The log file is attached
Your ECU has "programming not finished" flag raised. If next attempts to write with OBD-software can't recover this situation than you must clear this flag manually. This means to desolder 95040 eeprom chip from ECU board, read it, properly correct content of dump, write back and solder chip in your place. |
|
|
|
|
Logged
|
|
|
|
|
DJGonzo
Guest
|
|
« Reply #8 on: May 21, 2011, 04:35:02 PM »
|
|
|
tried to connect and reconnect nothing happened. The log file is attached
Your ECU has "programming not finished" flag raised. If next attempts to write with OBD-software can't recover this situation than you must clear this flag manually. This means to desolder 95040 eeprom chip from ECU board, read it, properly correct content of dump, write back and solder chip in your place. Or use a professional flashing tool  To the op: If you send it my way I can fix it without desoldering. I just had a 05 GLI do the same thing when I flashed it with Nefmoto. Car started fine but threw "Programming not finished" code. Reflashed with tool and hasn't come back since. PS: I doubt this is something APR did, but the GLI was APR tuned as well. |
|
|
|
|
Logged
|
|
|
|
kls
Full Member
Karma: +12/-0
Offline
Posts: 97
|
|
« Reply #9 on: May 22, 2011, 12:09:45 AM »
|
|
|
No need to actually remove the eeprom if it does need reprogramming. It can be reprogrammed in circuit with an SOIC clip and a programmer such as the UPA-USB.
|
|
|
|
|
Logged
|
|
|
|
|
gremlin
|
|
« Reply #10 on: May 22, 2011, 02:19:18 AM »
|
|
|
No need to actually remove the eeprom if it does need reprogramming. It can be reprogrammed in circuit with an SOIC clip and a programmer such as the UPA-USB.
From this point of view may say more - no need UPA, clips and etc to reprogram eeprom on the board. Just temporally convert ME7 ECU in "eeprom programmer". Get freely "minimon" soft, load in boot mode your specially programm and start it - that's all you need. But if you don't have a set of tools and experience desolder method is the simplest. |
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #11 on: May 23, 2011, 04:43:43 PM »
|
|
|
tried to connect and reconnect nothing happened. The log file is attached
You log file shows that you only tried to validate the flash memory layout. Validating the flash memory layout failed though, because reading from the flash memory was disabled. Entering programming mode in the ECU appears to have caused it to think that it has started programming and not completed. Normally the "programming not complete" flag is only set when you start writing to the ECU. Can you try validating the flash memory layout again, then click the disconnect button, then turn off the ignition. Then see if you can start the car. If that doesn't work, try validating flash memory layout again, then do a "check if flash matches" operation, then click the disconnect button, then turn off the ignition. Then see if you can start the car. If those two methods don't work, I think I can give you a test release with a code fix that may work. Normally after validating the memory layout, I do a quick checksum calculation to make the ECU happy, but I don't do that if validating the memory layout fails. So I should be able to give you a test release that will do the checksum calculation regardless of if validating the memory layout succeeds or not. |
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #12 on: May 24, 2011, 12:24:11 PM »
|
|
|
I have a test release that will hopefully fix this issue, with the car not starting after the Validate Memory Layout fails when RequestUpload is blocked by aftermarket software.
|
|
|
|
|
Logged
|
|
|
|
bigdawg56
Newbie
Karma: +2/-0
Offline
Posts: 10
|
|
« Reply #13 on: May 24, 2011, 04:47:15 PM »
|
|
|
I got the vendor to reflash the ecu for free so all is good now. thanks for all of your help and suggestions
|
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #14 on: May 24, 2011, 05:03:41 PM »
|
|
|
I will do some more testing myself on the 4Z7 907 551 AA ECU to make sure this doesn't happen again. It is possible that the APR trial software is doing something extra to make the car not start.
|
|
|
|
|
Logged
|
|
|
|
|
