Bi-turbo
Full Member
Karma: +1/-7
 Offline
Posts: 164
|
 |
« on: September 17, 2014, 10:47:06 AM »
|
|
|
551D
Done immo off with 95040 tool
.bin file off old ecu still 1024kb ecu can't post as it's commercial tune
Writes fine with galletto
Car fires up for 1 or 2 secs then conks out
Any ideas?
|
|
|
|
|
Logged
|
|
|
|
|
armageddon
|
|
« Reply #1 on: September 17, 2014, 01:09:50 PM »
|
|
|
try to flash other 95040.bin with immo off and see if it work.
friend of mine had is ECU "blocked" by an audi dealer, I simple put another 95040.bin on it and it worked
|
|
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #2 on: September 17, 2014, 01:31:09 PM »
|
|
|
It already had the immo off but I wrote another to it to be sure.
I did think about weather it needed the throttle body alignment or idle adjustment done with vcds
|
|
|
|
|
Logged
|
|
|
|
|
turboat
|
|
« Reply #3 on: September 17, 2014, 03:29:12 PM »
|
|
|
Odd, sounds a lot like immo stopping the engine. Are there any fault codes?
|
|
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #4 on: September 18, 2014, 12:08:29 AM »
|
|
|
Didnt scan it as i was getting frustrated as i had to walk back and forth from my house to garage to check it on the car 4 times after re-flashing.
I had another issue were on VCDS in engine it wouldnt bring up the ecu number it was just saying THIS-IS which i belive would be THIS-IS-THE-RAM-MEMORY whihc made me think somthing was scrambled?
Its a standard chip on the bored so not sure hwo it would scramble anything.
Its now not doing that after a reflash but still the start issue
|
|
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #5 on: September 18, 2014, 01:13:06 AM »
|
|
|
Just sprung to mind, is 551D ME7.1.1??
I think i has put the immo off bin for 7.5/7.1 on there
|
|
|
|
|
Logged
|
|
|
|
|
turboat
|
|
« Reply #6 on: September 18, 2014, 03:12:57 AM »
|
|
|
That may well be the problem! I always immo off the file I read from the ecu, rather than using a generic one. Post up the ori EEPROM and the immo off one
|
|
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #7 on: September 18, 2014, 03:39:50 AM »
|
|
|
I was goin to but i couldnt get your tool working
Ill try post them up later when im home
|
|
|
|
|
Logged
|
|
|
|
|
turboat
|
|
« Reply #8 on: September 18, 2014, 04:08:27 AM »
|
|
|
What was the issue you had?
|
|
|
|
|
Logged
|
|
|
|
Bi-turbo
Full Member
Karma: +1/-7
Offline
Posts: 164
|
|
« Reply #9 on: September 18, 2014, 05:07:14 AM »
|
|
|
it wouldnt run, somthing about python?
|
|
|
|
|
Logged
|
|
|
|
|
turboat
|
|
« Reply #10 on: September 18, 2014, 05:08:30 AM »
|
|
|
Use the version in the .zip, you need all the files in that zip in the same directory as the tool.
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #11 on: September 18, 2014, 09:43:28 AM »
|
|
|
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
|
