Vdub-dub
Full Member
Karma: +4/-1
 Offline
Posts: 136
|
 |
« on: September 27, 2014, 04:47:44 AM »
|
|
|
From bettle 2000 I can't seem to read the 24c02 chip with my willem programmer, what are people using to read it?
06a 906 018 ej
|
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +641/-21
Offline
Posts: 5640
|
|
« Reply #1 on: September 27, 2014, 05:26:52 AM »
|
|
|
Remove chip. Read it that way. I use GQ-4x.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
Vdub-dub
Full Member
Karma: +4/-1
Offline
Posts: 136
|
|
« Reply #2 on: September 27, 2014, 05:40:35 AM »
|
|
|
Oh so no other way?
With 95040 chip using test clip with willem I can read/write
I hate soldering lol
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #3 on: September 27, 2014, 10:31:00 AM »
|
|
|
Desoldering is the most reliable way. Other methods are/can be hit or miss.
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
|
eliotroyano
|
|
« Reply #4 on: September 27, 2014, 08:15:09 PM »
|
|
|
24C02 and other I2C similar serial eeproms are really tricky to read or write in circuit (ICSP). The main problem is it master-slave configuration and it bus timing associated for read and writing procedures. The best result until now, is desolder, work on it and re-solder.
|
|
|
|
|
Logged
|
|
|
|
|
TCSTigersClaw
|
|
« Reply #5 on: September 30, 2014, 12:53:56 AM »
|
|
|
with clip you may read it 10 times and you will get at least 3 different versions....  |
|
|
|
|
Logged
|
VAG cars newbie tuner  |
|
|
redtop
Jr. Member
Karma: +5/-0
Offline
Posts: 44
|
|
« Reply #6 on: September 30, 2014, 01:22:03 AM »
|
|
|
I'm reading and writing a 24c02 in circuit in an Alfa Romeo Bosch M2.10.x ECUs, using a Willem eprom without any problems. I guess it depends on the electronic design whether you can read it in circuit or not.
|
|
|
|
|
Logged
|
|
|
|
TijnCU
Hero Member
Karma: +60/-4
Offline
Posts: 690
flying brick
|
|
« Reply #7 on: October 01, 2014, 08:09:41 AM »
|
|
|
In my M3.2 ecu I was not able to read on the board, unsoldering did the trick. Also with Willem programmer.
|
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #8 on: October 01, 2014, 10:58:56 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
jamesr
Newbie
Karma: +1/-0
Offline
Posts: 15
|
|
« Reply #9 on: October 25, 2022, 07:50:19 PM »
|
|
|
Hi i've been trying to read a 24c02 from a m5.9.2 from a vw cabrio. It just reads all 00's i've tried the willem and a carprog. i'm trying to tune out the immobilizer. Any bits of wisdom ?? thanks!!
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #10 on: October 26, 2022, 12:37:27 AM »
|
|
|
Hi i've been trying to read a 24c02 from a m5.9.2 from a vw cabrio. It just reads all 00's i've tried the willem and a carprog. i'm trying to tune out the immobilizer. Any bits of wisdom ?? thanks!!
in circuit or desoldered? pictures? did you pick the right chip from the pcb? |
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #11 on: October 26, 2022, 02:53:24 PM »
|
|
|
Hi i've been trying to read a 24c02 from a m5.9.2 from a vw cabrio. It just reads all 00's i've tried the willem and a carprog. i'm trying to tune out the immobilizer. Any bits of wisdom ?? thanks!!
Some of this old ECUs have 93C46 EEPROM With number B58 on it |
|
|
|
|
Logged
|
|
|
|
jamesr
Newbie
Karma: +1/-0
Offline
Posts: 15
|
|
« Reply #12 on: October 27, 2022, 11:19:37 AM »
|
|
|
in circuit or desoldered?
pictures?
did you pick the right chip from the pcb?
I tried to use the car prog to read it in on the board I also tried probing it using a willem programmer. I didn't have success so I removed it and tried to read. Not having luck yet. ( Having problems with posting this) |
|
|
|
|
Logged
|
|
|
|
jamesr
Newbie
Karma: +1/-0
Offline
Posts: 15
|
|
« Reply #13 on: October 27, 2022, 11:20:34 AM »
|
|
|
Some of this old ECUs have 93C46 EEPROM
With number B58 on it
Thanks I'm trying to post some pics |
|
|
|
|
Logged
|
|
|
|
jamesr
Newbie
Karma: +1/-0
Offline
Posts: 15
|
|
« Reply #14 on: October 27, 2022, 11:30:55 AM »
|
|
|
Cant seem to post pictures it is a 037 906 018 C M5.9.2 V02
|
|
|
|
|
Logged
|
|
|
|
|
