Pages: [1]
Author Topic: 2.7t a6 tiptronic limp mode?  (Read 5872 times)
em.Euro.R18
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 219


« on: October 08, 2014, 12:40:24 PM »

Car will hit 2350mbar at wot during warmup but full operating temp or close you can see wbkda is limited to 20% while wped is at 100%. RL is limited to 116% because of rlsol_w but so for some reason spec is not following my ldrxn. Am I missing something? This is the first attempt on a 2.7t tiptronic.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12233


WWW
« Reply #1 on: October 08, 2014, 01:11:15 PM »

Please make sure ME7Logger outputs with the .csv extension, not the .log extension... i have .csv associated with ecuxplot ..
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
em.Euro.R18
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 219


« Reply #2 on: October 08, 2014, 01:42:23 PM »

I converted it to csv hope that works
Logged
ddillenger
Hero Member
*****

Karma: +638/-21
Offline Offline

Posts: 5640


« Reply #3 on: October 08, 2014, 02:09:37 PM »

From the looks of it boost request is stock?
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
em.Euro.R18
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 219


« Reply #4 on: October 08, 2014, 02:24:01 PM »

Logged
em.Euro.R18
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 219


« Reply #5 on: October 09, 2014, 05:21:20 AM »

LDR and IRL are not stock but I do believe it has something to do with a IAT limiter. I've recently noticed this only happens when the intake temps are high, coolant temp is at operating temp. Althought I've raised those area's 50-90*c in KFTARX to 1.02
« Last Edit: October 09, 2014, 05:27:09 AM by em.Euro.R18 » Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12233


WWW
« Reply #6 on: October 09, 2014, 04:05:16 PM »

You have busted wastegate lines. Don't bother tuning until you know how to verify the wastegates are working properly. Even worse, it is immediately obvious from your logs :/
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
em.Euro.R18
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 219


« Reply #7 on: October 10, 2014, 06:40:55 AM »

Before IAt's warmup request hits actual so I donno how the wastegate lines are busted. I'll check the wastegate lines but honestly doesn't make sense.... When Iat's warmed up I did notice actual overshot request a bit but nothing to cause concern even with 20% throttle position and 0% duty 1400mbar is near wastegate crack pressure.

Although looking more into it I'm overshooting to over 2000mbar so yeah you maybe right. I was focused on the IAt's because it would only happen fully warm which really kinda threw me off from the big picture. I'm fully capable of checking wastegate operation I appreciate the input.  Wink
« Last Edit: October 10, 2014, 06:51:09 AM by em.Euro.R18 » Logged
ddillenger
Hero Member
*****

Karma: +638/-21
Offline Offline

Posts: 5640


« Reply #8 on: October 10, 2014, 02:10:59 PM »

Unplug your N75 (electronically). Log the car. Post the log.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.036 seconds with 17 queries. (Pretty URLs adds 0.009s, 0q)