Double check voltage output before bench connecting

Pages: [1]

« previous next »

Author

Topic: Double check voltage output before bench connecting (Read 16471 times)

mounty

Full Member

Karma: +1/-0
Offline

Offline

Posts: 119

	Double check voltage output before bench connecting « on: October 21, 2014, 03:36:58 PM »

Well just as a friendly reminder to us all diy ers out there. Double check your voltage and amperage output before hooking up to your ecu on the bench.
I let my mom borrow my battery charger for a few days and didn't think anything of it since I've done It before more than once successful. Plugged cable into bench harness. Plugged cable I to computer. Plugged ecu into bench harness. Set my charger on 12v 2 amp. Hooked up power and when I turned my charger on I heard the transformer humming very loud. Looked at the amp gauge which was pegged at 100 plus amps. So now I need a new charger. And a new tdi ecu as this one will no longer start the car. Yay me.


	Logged

adam-

Hero Member

Karma: +124/-33
Offline

Offline

Posts: 2179

	Re: Double check voltage output before bench connecting « Reply #1 on: October 22, 2014, 04:30:24 AM »

Current has nothing to do with it, the ECU will draw what it needs, providing the charger can give the minimum of what it needs.

Using a charger that can provide over 100 amps is seriously excessive though. Sounds like there's a massive short though.

100 amps at 14 volts is over 1400 watts. As you said, the ECU won't need more than an amp, so that's 12 watts.

Provided the charger is outputting 12v and the harness is fine, there should be no problem. I think the charger is broken though, and that's what's killed your ECU.


	Logged

turboat

Hero Member

Karma: +45/-3
Offline

Offline

Posts: 619

	Re: Double check voltage output before bench connecting « Reply #2 on: October 22, 2014, 04:58:38 AM »

+1.

A car battery will push 70A+ for cranking and its fine to connect an ECU to that.


	Logged

mounty

Full Member

Karma: +1/-0
Offline

Offline

Posts: 119

	Re: Double check voltage output before bench connecting « Reply #3 on: October 22, 2014, 01:59:21 PM »

Seeing as how the charger was set on 2 amp 12v charge and it still put out well over a hundred amps as the gauge was pegged 100+ I know it's my battery charger that killed my ecu. Especially since I had removed it from the car 5 minutes prior to that.

Now I have a tdi ecu that was a auto car. Time to figure out how to deal with the immo.


	Logged

nyet

Administrator
Hero Member

Karma: +608/-168
Offline

Offline

Posts: 12270

	Re: Double check voltage output before bench connecting « Reply #4 on: October 22, 2014, 02:02:11 PM »

Quote from: mounty on October 22, 2014, 01:59:21 PM

Seeing as how the charger was set on 2 amp 12v charge

Don't use a charger as a power supply. Always a bad idea.


	Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex

MadCow

Full Member

Karma: +3/-1
Offline

Offline

Posts: 108

	Re: Double check voltage output before bench connecting « Reply #5 on: October 31, 2014, 06:57:08 PM »

Next time use an old computer power supply, doesn't even have to be a good one, anything will work.


	Logged

nyet

Administrator
Hero Member

Karma: +608/-168
Offline

Offline

Posts: 12270

	Re: Double check voltage output before bench connecting « Reply #6 on: October 31, 2014, 07:09:09 PM »

You can even use a 12v-14v wallwart.


	Logged

ddillenger

Hero Member

Karma: +641/-21
Offline

Offline

Posts: 5640

	Re: Double check voltage output before bench connecting « Reply #7 on: October 31, 2014, 07:11:35 PM »

Quote from: nyet on October 31, 2014, 07:09:09 PM

You can even use a 12v-14v wallwart.

Can confirm

Source:

I am a walwart.


	Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM

mounty

Full Member

Karma: +1/-0
Offline

Offline

Posts: 119

	Re: Double check voltage output before bench connecting « Reply #8 on: November 05, 2014, 01:58:00 AM »

So far a 14v 1.5 amp supply from a no longer needed walkie radio charger is doing the job. New software is making it difficult to rea . But seems to be powering the ecu and I am able to read from mpps so I'm content.


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 27, 2024, 07:08:37 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search