Newbie with VAGcom - Full Read failed

Pages: [1]

« previous next »

Author

Topic: Newbie with VAGcom - Full Read failed (Read 8759 times)

vtraudt

Sr. Member

Karma: +4/-7
Offline

Offline

Posts: 377

	Newbie with VAGcom - Full Read failed « on: June 17, 2011, 08:23:57 AM »

Brand newbie, so go easy on me!
Have original VAGcom KII-USB. Unchecked "Boot in intelligent mode".
Car is 2002 Audi Allroad manual.
ME7 29F800BB memory layout (was told that is the right one).
Current have custom stage 2 file
Nefmoto communicates.
Able to "Read ECU Info"
Able to "Read DTCs".

When running Full Read Flash, I get an error after about 3%.

Any suggestions what may be wrong?

I would like to install the stock file (and later be able to flash tune changes).
Certainly, I will not attempt (I don't have a spare ECU standing by) to write a file until I am at least able to READ.


	Logged

2002 Allroad 2.7T 6spd stage 2
1998 A4 1.8T 5spd stage 3
1996 A4 2.8 auto stock

vwaudiguy

Hero Member

Karma: +53/-37
Offline

Offline

Posts: 2024

	Re: Newbie with VAGcom - Full Read failed « Reply #1 on: June 17, 2011, 12:59:53 PM »

Tony will most likely want you to post the log. Usually you're not able to read flashed (tuned) files through the OBD, which would have been my first guess as to why you have an issue. The fact that it even begins to read I think may rule this theory out though.


	Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."

vtraudt

Sr. Member

Karma: +4/-7
Offline

Offline

Posts: 377

	Re: Newbie with VAGcom - Full Read failed « Reply #2 on: July 19, 2011, 08:19:40 PM »

Ordered a cheap ebay adapter, worked right away. Not sure why the Rosstech does not work.


	Logged

2002 Allroad 2.7T 6spd stage 2
1998 A4 1.8T 5spd stage 3
1996 A4 2.8 auto stock

vtraudt

Sr. Member

Karma: +4/-7
Offline

Offline

Posts: 377

	Re: Newbie with VAGcom - Full Read failed « Reply #3 on: July 24, 2011, 06:57:53 AM »

The other I tried to save the stock file of a 2004 Allroad 2.7T auto, using the blue ebay cable I successfully have used on my 2002 Allroad 2.7T manual.

It connected as expected, but the 'full read' failed after a few seconds.
Car did NOT start after that, VAGcom reported a 'incomplete read' or so.

Tried a second time, and this time read went through without a hitch and was able to save the stock file.

Note: IIRC, the 'erase DTC codes' came back with error as well.

Is there anything special on the 2004 Allroad that causes it to behave differently than my 2002 Allroad?


	Logged

2002 Allroad 2.7T 6spd stage 2
1998 A4 1.8T 5spd stage 3
1996 A4 2.8 auto stock

Tony@NefMoto

Administrator
Hero Member

Karma: +132/-4
Offline

Offline

Posts: 1389

2001.5 Audi S4 Stage 3

	Re: Newbie with VAGcom - Full Read failed « Reply #4 on: August 29, 2011, 11:40:06 PM »

The Ross-Tech KII cables do not support true dumb mode pass through and that is why the read fails.


	Logged

Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 26, 2024, 03:47:13 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search