NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors
Pages: [1]
« previous next »
Author Topic: AUDI A6 C5 2.4V6 AML ME7.1 3B0907552AP - how to numb rear o2 sensors  (Read 5378 times)
bendzji
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 10
I'm looking to try to numb the sensivity of the rear o2 sensors -I'm getting P0420 , P0430 DTC.

Propably it happens beacause i have a LPG conversion so the exhaust gases are diffrent than on petrol ( no DTC when using it )

I found on the forum and WIKI that i should change these parameters:

    AHKATMN (0x18672) - leave alone
    AHKATMX (0x18673) - set to max
    AHKATS (0x18674) - set to max
    AHKATSB (0x18675) - set to max

Are these adresses the same in my ECU eeprom? Cannot find any XDF but it's a ME7.1.
In my BIN all of these values are the same.
« Last Edit: December 03, 2014, 02:06:30 PM by bendzji » Logged
bendzji
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 10
« Reply #1 on: December 02, 2014, 03:37:52 PM »
After comparing bin files with a M-Box i suppose that in my bin these parameters are on:

AHKATMN -0x18662
AHKATMX -0x18663
AHKATS - 0x18664
AHKATSB -0x18665

Am i correct?

  
I'm looking for a second ECU to play with on bench - what about other part number , let's say 3B0907552 but with F , AN or other?
« Last Edit: December 03, 2014, 02:02:08 AM by bendzji » Logged
bendzji
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 10
« Reply #2 on: September 30, 2015, 02:20:29 AM »
I've changed:

CDKAT  - 181A0
CWDLSAHK - 18653

and It works , they are almost in the same place as in 3B0907552AN
« Last Edit: October 20, 2015, 02:44:23 PM by bendzji » Logged
kris1855
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
Quote from: bendzji on September 30, 2015, 02:20:29 AM
I've changed:

CDKAT  - 181A0
CWDLSAHK - 18653

and It works , they are almost in the same place as in 3B0907552AN



Hello, I am at the stage of blocking diagnostic probes behind the catalyst.
I opened the bin file from ecu into the hex editor and the question in what table should I change it to block the probes.
Audi a6 c5 2.4 AML 3B0907552AN
Maybe someone would suggest where to look for it.
Logged
macxxx
Sr. Member
****

Karma: +30/-1
Offline Offline

Posts: 498
You have all the info here Wink
Logged
kris1855
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
Quote from: macxxx on May 20, 2018, 05:06:20 AM
You have all the info here Wink

I understand that in the editor hex he finds the address CDKAT - 181A0
CWDLSAHK - 18653
and I change from 01 to 00 ??
Do I understand correctly?
Logged
macxxx
Sr. Member
****

Karma: +30/-1
Offline Offline

Posts: 498
You didnt try?
Logged
kris1855
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
Quote from: macxxx on May 20, 2018, 11:25:33 AM
You didnt try?
I'm asking, because I do not want to make any mistakes.
In the picture, I marked the value 01 and I have to change it to 00.
Make a check sum and upload to ecu.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 27, 2024, 08:56:10 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.026 seconds with 17 queries. (Pretty URLs adds 0s, 0q)