|
|
|
ddillenger
|
 |
« Reply #16 on: November 17, 2014, 04:02:36 PM »
|
|
|
Considering there are 2 ESKONF, yes. One is for variant coding. Did you change both? |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
narf0815
Full Member
Karma: +2/-1
 Offline
Posts: 87
|
|
« Reply #17 on: November 18, 2014, 12:56:52 AM »
|
|
|
Thanks again  Yes, there are 2 ESKONF: @10ED1: AA FF 00 30 E3 F8 30 which i had changed to: AA FF 00 33 E3 F8 30 and @10ED8: AA FF 00 30 23 F8 30 which i had changed to: AA FF 00 33 23 F8 30 could the "23" be the problem? But this should refer to the BKV? E3 = No BKV and 23= BKV existent..of course i have an BKV (or not???)? Sounds Strange to me... What should i do now? Set the second to the same as the first? |
|
|
|
« Last Edit: November 18, 2014, 10:57:08 AM by narf0815 »
|
Logged
|
|
|
|
narf0815
Full Member
Karma: +2/-1
Offline
Posts: 87
|
|
« Reply #18 on: November 20, 2014, 07:59:33 AM »
|
|
|
CDLDP @ 181A8
CDTES @ 181B2
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #19 on: November 20, 2014, 09:20:03 AM »
|
|
|
I posted about this before. When I did it, I ended up error classing it  |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
narf0815
Full Member
Karma: +2/-1
Offline
Posts: 87
|
|
« Reply #20 on: November 20, 2014, 10:35:57 AM »
|
|
|
Sorry, what did you mean with: Ended up error classing it?
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #21 on: November 20, 2014, 10:53:09 AM »
|
|
|
CLALDP
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
|
ddillenger
|
|
« Reply #22 on: November 20, 2014, 10:53:28 AM »
|
|
|
CLALDPE
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
narf0815
Full Member
Karma: +2/-1
Offline
Posts: 87
|
|
« Reply #23 on: December 14, 2014, 09:50:32 AM »
|
|
|
CLALDPE
Do you mean i should do at 184f9 = 00 or FF? |
|
|
|
|
Logged
|
|
|
|
narf0815
Full Member
Karma: +2/-1
Offline
Posts: 87
|
|
« Reply #24 on: January 16, 2015, 12:50:07 PM »
|
|
|
Hi,
i don't know what's wrong...
CDLDP @ 181A8 = 00
CDTES @ 181B2 = 00
CLATEVE @ 18520 = 00
CLALDPE @ 184f9 = 00
ESKONF @ 10ED5 = EF
still have the error and yellow light...
File is the community stage1 518ak
Not checksumed..
|
|
|
|
|
Logged
|
|
|
|
|
thelastleroy
|
|
« Reply #25 on: January 17, 2015, 09:48:16 AM »
|
|
|
Are you trying to reprogram the evap as In not equipped from factory, or just prevent dtc's? Are your addreses confirmed correct?
I had a few evap codes on my car (I can't remember exactly which ones...leak detection pump and incorrect flow purge valve I believe) and all that was necessary was to 0 the CDLDP and CDTES parameters. I do however still have all equipment still plugged in.
My readiness for evap is now "not available", but I have all other systems legit set ready so my emissions test will (hopefully) pass.
As far as I have been able to research, nobody has found a way to set readiness on evap by fooling the ecu. I'm sure it's possible with a hack.
First thing to do IMO is set everything back to stock and confirm your addresses. According to the wiki what you did should have worked if everything is correctly defined.
|
|
|
|
|
Logged
|
|
|
|
narf0815
Full Member
Karma: +2/-1
Offline
Posts: 87
|
|
« Reply #26 on: January 18, 2015, 08:47:46 AM »
|
|
|
i got addresses for CDLDP & CDTES from the stage1v6.xdf.
CLATEVE & CLALDPE from ddillenger on page 1 of this threat.
Yes, i try to reprogram cause europe models don't have it from factory.
If i take the original 518AK 003 file i only had to set CDLDP to 0 and everything is fine...but i have problems with the community stage 1 file.
Maybe a bug in the file?
|
|
|
|
« Last Edit: January 18, 2015, 08:51:18 AM by narf0815 »
|
Logged
|
|
|
|
|
thelastleroy
|
|
« Reply #27 on: January 18, 2015, 11:19:41 AM »
|
|
|
Which file a are you running? There have been a few revisions. I may have left the CDLDP and CDTES and mslub mods in a few of them by accident, I have removed SAI and defeated the evap for my car specifically.
CDLDP and CDTES were both "1" on thecstock file, original mslub values can be found in the stock file on page 1 of the stage 1 thread.
Try only setting CDLDP and CDTES to "0" only and see if it works. I have no evap codes with this arrangement, all other parameters are stock.
|
|
|
|
|
Logged
|
|
|
|
narf0815
Full Member
Karma: +2/-1
Offline
Posts: 87
|
|
« Reply #28 on: January 18, 2015, 11:53:00 AM »
|
|
|
Currently i have flashed v7.
MSLUB has stock, like the 518AK 003 file, values.
I will retry but i'm sure i already tested with CDLDP and CDTES to 0...
|
|
|
|
|
Logged
|
|
|
|
narf0815
Full Member
Karma: +2/-1
Offline
Posts: 87
|
|
« Reply #29 on: January 19, 2015, 10:48:35 AM »
|
|
|
So, i have set CDLDP and CDTES to 0
Everything else to stock stage1 v7 except MSULB from stock 518AK 003.
I still have the error, yellow light BUT EVAP passed??
And CDSLS is set to 1 but failed...
|
|
|
|
« Last Edit: January 19, 2015, 10:51:32 AM by narf0815 »
|
Logged
|
|
|
|
|
