|
rob.mwpropane
|
 |
« on: June 30, 2011, 07:48:46 PM »
|
|
|
Hi all, I finally got around to bench flashing a stock ECU. It connects fine but when I go to read the flash I get ECU reports that security access is not supported.  ?, I'm sure it's something simple I'm overlooking, thanks in advance! |
|
|
|
|
Logged
|
This has nothing to do with cars but you can see my glorifying job at, www.MWPropane.com |
|
|
carlossus
Sr. Member
Karma: +38/-0
 Offline
Posts: 394
Leon Curpa Stg1+
|
|
« Reply #1 on: July 01, 2011, 12:10:56 AM »
|
|
|
Hi all, I finally got around to bench flashing a stock ECU. It connects fine but when I go to read the flash I get ECU reports that security access is not supported. ?, I'm sure it's something simple I'm overlooking, thanks in advance! My ECU will not read / write unless it has sucessfully paired with the cluster i.e. the immobilizer is happy. So I can only do it in the car unless I deactivate the immo. Also, if you search for "security access is not supported" a few other threads come up, maybe there are other reasons too. -c |
|
|
|
|
Logged
|
|
|
|
|
rob.mwpropane
|
|
« Reply #2 on: July 01, 2011, 02:44:25 AM »
|
|
|
Yeah, I had a hunch that may have been the problem. It can read and cler DTC's fine, but won't read the flash. Thanks for the reply, I will try reading when it's in the car.
|
|
|
|
|
Logged
|
This has nothing to do with cars but you can see my glorifying job at, www.MWPropane.com |
|
|
chienliu1972
Full Member
Karma: +5/-0
Offline
Posts: 50
|
|
« Reply #3 on: August 09, 2011, 07:42:26 PM »
|
|
|
My Car is 2003 VW Sharan 1.8T AG5. Yesterday I tried to read my ECU, but it was failed. I upload the log file as attached. Could any body advise how to solve?
I remember that the first time the chip remapping service supplier also occured the same problem. Finally they took out the ECU chip and soldered another chip(29F800BB) back. Than it was strange, the ECU could be readed and wrote from OBD II again.
|
|
|
|
|
Logged
|
|
|
|
|
pvl
|
|
« Reply #4 on: August 10, 2011, 09:46:55 AM »
|
|
|
Untill Tony finds a way to do benchflashes with the KKL leads, this issue will be
not solved. The immobiliser is the problem.
Solution : kwp2000+ interface + special ME7edtion software and it will be read
and writeable in the car, and if it fails, via benchflashcable directly onto the ecu.
No opening up.
Better tip, but slightly more expensive : mpps flasher.
Both tested on multiple ME7.5.x ecu''s.
Cheers,
PvL
|
|
|
|
|
Logged
|
|
|
|
infinkc
Full Member
Karma: +6/-1
Offline
Posts: 94
|
|
« Reply #5 on: August 10, 2011, 03:17:11 PM »
|
|
|
Untill Tony finds a way to do benchflashes with the KKL leads, this issue will be
not solved. The immobiliser is the problem.
Solution : kwp2000+ interface + special ME7edtion software and it will be read
and writeable in the car, and if it fails, via benchflashcable directly onto the ecu.
No opening up.
Better tip, but slightly more expensive : mpps flasher.
Both tested on multiple ME7.5.x ecu''s.
Cheers,
PvL
what if the immobilizer is disabled, can it be flashed, then immobilizer re-enabled? not sure where your located but i could flash it for you with a mpps. |
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #6 on: August 10, 2011, 08:37:06 PM »
|
|
|
I was under the impression that the nefmoto software will not do any bench flashing regardless of immo on/off. This has been the case with me anyway. I thought maybe it was done to keep noobs from going flash crazy...  |
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
chienliu1972
Full Member
Karma: +5/-0
Offline
Posts: 50
|
|
« Reply #7 on: August 13, 2011, 07:37:10 PM »
|
|
|
I have not successfully read out the ECU of my car, VW Sharan 1.8T AG5. However, I have successfully read out three(3) cars with the same model car, VW Sharan 1.8T AG5, which tunned by ABT, MTM, and VW original. I post these files on the forum for reference and checking. I think that NefMoto is OK. The problem is the battery voltage of the car. Because all the three(3) cars with the healthy battery, reading out the ECU is very smooth.
The battery voltage may not good enough for steady state of ECU reading. Thus, the connection to ECU is failed. I would try again when I change a new battery, then report to you.
|
|
|
|
|
Logged
|
|
|
|
chienliu1972
Full Member
Karma: +5/-0
Offline
Posts: 50
|
|
« Reply #8 on: August 23, 2011, 07:49:33 AM »
|
|
|
Hi! I have tried again to read out the ECU software, But it is failed. The log file of NefMoto is as follows,
23/??/2011 10:08:12.023: USER: Security access granted.
23/??/2011 10:08:12.034: USER: Validating flash memory starts at 0x00800000 and ends at 0x00900000.
23/??/2011 10:08:12.045: LOG: Sent message with service ID RequestUpload
23/??/2011 10:08:12.076: LOG: Received message with service ID NegativeResponse
23/??/2011 10:08:12.079: LOG: Received negative response for service ID: RequestUpload, with response code: ServiceNotSupported
23/??/2011 10:08:12.083: USER: Validation failed, ECU reports RequestUpload service is not supported. RequestUpload may have been disabled by aftermarket engine software.
23/??/2011 10:08:12.091: LOG: Validating flashed data checksum for address range 0x00900000 to 0x00900001.
23/??/2011 10:08:12.103: LOG: Sent message with service ID StartRoutineByLocalIdentifier
23/??/2011 10:08:12.135: LOG: Received message with service ID StartRoutineByLocalIdentifierPositiveResponse
23/??/2011 10:08:12.140: LOG: Sent message with service ID RequestRoutineResultsByLocalIdentifier
23/??/2011 10:08:12.166: LOG: Received message with service ID NegativeResponse
23/??/2011 10:08:12.168: LOG: Received negative response for service ID: RequestRoutineResultsByLocalIdentifier, with response code: BlockTransferDataChecksumError
23/??/2011 10:08:12.170: LOG: Checksum is incorrect.
23/??/2011 10:08:12.172: USER: 100% complete.
23/??/2011 10:08:12.179: USER: Validating memory layout failed.
Validation did not complete.
23/??/2011 10:08:14.642: LOG: Sent message with service ID TesterPresent
23/??/2011 10:08:14.670: LOG: Received message with service ID TesterPresentPositiveReponse
23/??/2011 10:08:16.469: USER: Restoring Windows sleep mode.
Could anyone advise how to access the next step? What should I do?
|
|
|
|
|
Logged
|
|
|
|
robin
Full Member
Karma: +20/-1
Offline
Posts: 139
|
|
« Reply #9 on: October 04, 2011, 09:59:15 AM »
|
|
|
I've had luck with just clicking 'read entire flash' again and it will pick up from that point.
|
|
|
|
|
Logged
|
|
|
|
|
