s3 8L - stage 3 - Boost drop at 6000rpm

Pages: [1]

« previous next »

Author

Topic: s3 8L - stage 3 - Boost drop at 6000rpm (Read 8715 times)

madswp

Full Member

Karma: +3/-0
Offline

Offline

Posts: 102

	s3 8L - stage 3 - Boost drop at 6000rpm « on: March 19, 2015, 01:32:23 PM »

Hello Nefmoto's Wink

long time since i messed around with me7 ecu's. but now i have a problem:

Car specs:
audi s3 8L 225hp BAM engine.
upgraded h-beam conrods,
siemens deka 630 ml injectors
stock pistons with 9.0:1 CR
garrett gt3071R A/R 0.64

Car runs great up to 6000rpm then boost drops from ~2500mbar to ~1600mbar. this is happening on every run i take and doesn't matter how much load i apply (3-4-5 gear, all the same at 6000rpm)
EGT reaches max 850c, Lambda ~0.82. ignition retard ~3degrees.
adjusting WGDC at KFLDRL makes absolutely no differences. i can control boost fine under 6000rpm, but over it does always drop.
i have tried finetuning several LDR based maps (even locking KFLDRL up to 95%), but makes no differences. as you can see on attached log, then the boost is really quickly dropping.
could a maxed out MAF sensor cause this behavior? it reaches 4.88V on signal line.
wastegate cracking pressure is set to 0.7bar.
i am really starting to think it might be a hardware problem, maybe wastegate gets blown open by exhaust pressure.

what are your thoughts on this?

Regards


« Last Edit: March 19, 2015, 01:36:57 PM by madswp »	Logged

prj

Hero Member

Karma: +1072/-480
Offline

Offline

Posts: 6035

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #1 on: March 19, 2015, 02:21:49 PM »

Can you show a photo of your intake setup? Filter to turbo?
It is probably collapsing.


	Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches

fredrik_a

Full Member

Karma: +25/-0
Offline

Offline

Posts: 221

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #2 on: March 20, 2015, 02:48:26 AM »

I usually fit a pressure gauge fitting after the air filter for calibration purposes. If it starts to read pressure levels below normal atmospheric pressure, the air filter can not flow enough.


	Logged

prj

Hero Member

Karma: +1072/-480
Offline

Offline

Posts: 6035

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #3 on: March 20, 2015, 06:09:25 AM »

Quote from: fredrik_a on March 20, 2015, 02:48:26 AM

I usually fit a pressure gauge fitting after the air filter for calibration purposes. If it starts to read pressure levels below normal atmospheric pressure, the air filter can not flow enough.

That's not quite right, most filters have a small pressure drop from what I have tested.
And if you have a big soft silicone hose, then even 0.1 bar of "negative boost" can collapse it.

@OP, check your intake, make sure you are not using any loose silicone hose. Do a run without the air filter and see if without the air filter the problem goes away (just dont drive around like that).
If you have a dyno, you can visually confirm it.


	Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches

janne

Full Member

Karma: +2/-0
Offline

Offline

Posts: 50

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #4 on: March 23, 2015, 03:52:40 AM »

Can be stupid idea, but look KFMDBGRG


	Logged

madswp

Full Member

Karma: +3/-0
Offline

Offline

Posts: 102

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #5 on: March 25, 2015, 12:04:40 PM »

Thank you for your replies! Wink

It was the stock air filter case which was the problem like PRJ said. It did colapse the intake hoses between turbo and filter.

btw. can't recommend samco sport hoses for intake. They are very soft compared to other types i have tried, (know filter and box was the issue here, but anyway)

Mads


	Logged

prj

Hero Member

Karma: +1072/-480
Offline

Offline

Posts: 6035

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #6 on: March 25, 2015, 12:11:37 PM »

Problem solved then.


	Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches

aef

Hero Member

Karma: +69/-46
Offline

Offline

Posts: 1601

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #7 on: March 26, 2015, 12:23:10 AM »

Im interested in Results with the gt30 with 9:1cr


	Logged

fredrik_a

Full Member

Karma: +25/-0
Offline

Offline

Posts: 221

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #8 on: March 26, 2015, 03:57:55 AM »

What is the real maximum boost pressure? It seems to be beyond the limit of the MAP-sensor (4.600-5.600 rpms) at least, or is it insanely well calibrated for 1.55 bars of boost


« Last Edit: March 26, 2015, 03:59:43 AM by fredrik_a »	Logged

madswp

Full Member

Karma: +3/-0
Offline

Offline

Posts: 102

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #9 on: March 26, 2015, 01:27:03 PM »

the car is absolutely stock right now besides conrods, turbo and fuel system. i did play a little on dyno and pushing it to the edge. it did 352hp@5700rpm and 470nm. but with a lot backpressure in exhaust (over 1.5bar on stock exhaust after cat) and i am also guessing the intake could be better (stock airfilter and modded box). the boost is dropping down to ~1.3 bar at 7000rpm.
max boost was locked by KFLDRL to 1.6bar, so close to 1.55.

right now it got 319hp at 6500rpm. at 2.050mbar absolute on octane 95 and ignition between 16-19 degrees at higher rpm . i think thats a little more sane with that setup Wink

the tuning continues.....


	Logged

madswp

Full Member

Karma: +3/-0
Offline

Offline

Posts: 102

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #10 on: March 26, 2015, 01:36:12 PM »

btw another question:

why does the engine run VERY BAD without airfilter? it cant rev at all and feel like its cutting ignition when driving. is that normal on ME7 or is it just something thats needs to be calibrated?


	Logged

nyet

Administrator
Hero Member

Karma: +607/-168
Offline

Offline

Posts: 12268

	Re: s3 8L - stage 3 - Boost drop at 6000rpm « Reply #11 on: March 26, 2015, 06:07:52 PM »

Quote from: madswp on March 26, 2015, 01:36:12 PM

The MAF requires a reasonable air column.

Full airbox is the best. Anything else, forget it, you'll be fighting fuel trims until the end of time.


	Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 25, 2024, 04:51:42 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search