NefMoto > Technical > Flashing and Chipping > SWAP VAG Bosch ME 7.1.1 ECU PLEASE HELP
Pages: [1]
« previous next »
Author Topic: SWAP VAG Bosch ME 7.1.1 ECU PLEASE HELP  (Read 9073 times)
R32VAG
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 20
« on: May 06, 2015, 11:41:33 PM »
Hello,


my bricked one is OE Number: 022906032CE

Can i use every 022906032 Number? So i can Clone the Flash Chip and the EEprom to the new one.
For example i want to buy a 022906032GJ. I think this is the same ecu. Explained the eprom and the eeprom. So can i use this ecu when i clone the eprom and eeprom data from the old one to the new one?
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024
« Reply #1 on: May 07, 2015, 09:25:42 AM »
Have you tried bootmode and flashing another bin?
Logged
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
R32VAG
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 20
« Reply #2 on: May 07, 2015, 01:52:12 PM »
I have installed a new eprom chip with new software. Same failure..
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024
« Reply #3 on: May 08, 2015, 10:37:52 AM »
In reference to your original question, I believe if the Bosch number matches (ex. 0261207881) I think it should work. Not 100% on that though.
Logged
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Lionborg
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11
« Reply #4 on: May 08, 2015, 11:01:05 AM »
Im quite sure that you cannot use all ECU's with the Bosch number 022906032 as 1.8T's also has this number. The ECU must be of the same car (ie Golf 5 R32 manual). The letters dosen't have to be the same necessarily but would be preferred.
Logged
tjwasiak
Sr. Member
****

Karma: +26/-0
Offline Offline

Posts: 420
« Reply #5 on: May 08, 2015, 11:34:08 AM »
Quote from: Lionborg on May 08, 2015, 11:01:05 AM
Im quite sure that you cannot use all ECU's with the Bosch number 022906032 as 1.8T's also has this number.
You are wrong:
 - ABC906032XY is not a Bosch number, it is VAG part number
 - 1.8T ME7.5 wideband ECUs are 06A906032
 - VR6 ECUs are 022906032
Logged
Lionborg
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11
« Reply #6 on: May 08, 2015, 12:09:30 PM »
Ok i see about the Bosch number vs VAG part number, and also verified the 1.8T number. But the mk4 2.8 VR6 (4motion) also has a 022906032 ECU even though its a ME7.1 and not R32 ME7.1.1 so i still wouldnt buy just any ecu with the 022906032 number on it.
Logged
R32VAG
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 20
« Reply #7 on: May 10, 2015, 12:40:15 AM »
So my question was. Can i buy this ecu: 022906032KT (Its from a Audi TT with the SAME machinecode BUB.) Then i desolder the flash chip and immobilizer chip from my old ecu and installed it on the new ecu?
Logged
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640
« Reply #8 on: May 10, 2015, 12:46:13 AM »
Quote from: R32VAG on May 10, 2015, 12:40:15 AM
So my question was. Can i buy this ecu: 022906032KT (Its from a Audi TT with the SAME machinecode BUB.) Then i desolder the flash chip and immobilizer chip from my old ecu and installed it on the new ecu?

The later ST10 ME7 ecus cannot simply be crossflashed. If you can run the software that is on the ecu, then you can use the ecu. Otherwise, no, you should get an exact match (or a tool that can write the MPC content).
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
wannabee900
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 42
« Reply #9 on: August 24, 2015, 06:31:11 AM »
Quote from: ddillenger on May 10, 2015, 12:46:13 AM
The later ST10 ME7 ecus cannot simply be crossflashed. If you can run the software that is on the ecu, then you can use the ecu. Otherwise, no, you should get an exact match (or a tool that can write the MPC content).
Are you referring to rom in primary or secondary ST10 cpu or both?
Logged
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640
« Reply #10 on: August 24, 2015, 01:25:39 PM »
ST10 isn't read only.

You can change the processor content if you have the appropriate tools.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 30, 2024, 04:29:07 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.026 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)