Rail pressure Med9.1

Pages: [1]

« previous next »

Author

Topic: Rail pressure Med9.1 (Read 5684 times)

Iceman160785

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Rail pressure Med9.1 « on: June 12, 2015, 02:28:35 PM »

Hi friends!

Please can you be kind and tell me! Huh

Is it not possible to request higher than 129.99bar fuel pressure on this ECU? Its a Audi S3 2.0T BHZ engine. I have tryed to raise fuel pressure to 136bar. but can not make ecu to request higher than 129.99bar when i am logging it. i have uppgraded Loba fuel pump and 140bar fuel regulatlr on rail. THanks.


	Logged

ericpaulyoung

Full Member

Karma: +5/-0
Offline

Offline

Posts: 149

	Re: Rail pressure Med9.1 « Reply #1 on: June 12, 2015, 04:04:19 PM »

Yes you can


	Logged

Iceman160785

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Re: Rail pressure Med9.1 « Reply #2 on: June 13, 2015, 01:11:29 PM »

Quote from: ericpaulyoung on June 12, 2015, 04:04:19 PM

Yes you can

Thanks!:) Can it be becouse the rail limiter is set to low? hope somone will take their time to answaer a neewbi!:)


« Last Edit: June 13, 2015, 01:36:59 PM by Iceman160785 »	Logged

Iceman160785

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Re: Rail pressure Med9.1 « Reply #3 on: June 13, 2015, 01:35:19 PM »

Quote from: Iceman160785 on June 13, 2015, 01:11:29 PM

Thanks!:) Can be becouse the rail limiter is set to low? hope somone will take their time to answaer a neewbi! Embarrassed


	Logged

Beaviz

Full Member

Karma: +8/-4
Offline

Offline

Posts: 190

	Re: Rail pressure Med9.1 « Reply #4 on: June 14, 2015, 03:05:57 AM »

Tell me the maps you have changed and I will tell you what you missed.


	Logged

Iceman160785

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Re: Rail pressure Med9.1 « Reply #5 on: June 18, 2015, 12:17:39 PM »

Thanks Beaviz! I reallt appreciate that! i think i found a way to request the pessure now.

But i see that ecu dont request the same high rail presure on each full throotle run. Some times it request 136bar all the way to redline. but some times it only request as low as 90-110bar only on a fulle throttle run. it meets desired AF 0.81 all the way but pulse widt is higher at 8-10ms when it request lower rail pressure. what detirmes requested rail pressure from ecu? does ecu request lower rail pressure if desired af is meet? Huh

Thanks all help is appreciated!!:)


	Logged

Beaviz

Full Member

Karma: +8/-4
Offline

Offline

Posts: 190

	Re: Rail pressure Med9.1 « Reply #6 on: June 19, 2015, 12:43:01 AM »

The requested rail pressure should be consistent if you corrected all the required maps.

It will not drop if the requested AFR is met. The ECU will adapt the injection timing in that case.

Which of the KFPRSOL maps did you correct?


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 28, 2024, 08:58:47 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search