Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
 Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
 |
« Reply #30 on: January 22, 2011, 02:51:10 PM »
|
|
|
Which protocol KWP1281 or KWP2000?
The docs in the communication protocol sub forum should contain all this info.
|
|
|
|
|
Logged
|
|
|
|
technic
Full Member
Karma: +18/-5
Offline
Posts: 227
|
|
« Reply #31 on: January 22, 2011, 03:53:10 PM »
|
|
|
KWP1281. Found it. I missed the textfile in the protocol subfoum.
Thanks.
|
|
|
|
|
Logged
|
|
|
|
|
eliotroyano
|
|
« Reply #32 on: February 20, 2011, 07:02:13 PM »
|
|
|
I have read the Eeprom of M383 & M592 (both KW1281) ECUs using Monoscan with great sucess. I also can read RAM too. But I was unable to write it. About the SOIC8 clip I have a Pomona one but reading the eeprom was a bit tricky. I could read a M592 ECU that I have been testing, but M383 doesn't allow at all. I tryied with ECU powered too without luck.
|
|
|
|
|
Logged
|
|
|
|
|
pvl
|
|
« Reply #33 on: February 21, 2011, 05:51:45 AM »
|
|
|
Hi eliotroyano,
Could you specify what kind of thing this is : 'monoscan'
Where you able to read-out the complete content of the eeprom and flashrom ?
I'm highly interested in this .
Any extra info is greatly appreciated !
Thanks,
PvL
|
|
|
|
|
Logged
|
|
|
|
|
|
|
pvl
|
|
« Reply #35 on: February 21, 2011, 06:23:53 PM »
|
|
|
@ eliotroyano :
My friend, thank you VERY VERY much for this great find. I will have a look to it, asap
and report back.
Hopefully the author also implements writing of eeproms within time. That would be
really great.
I'm going to test this software asap.
Cheers,
PvL
|
|
|
|
|
Logged
|
|
|
|
Giannis
Full Member
Karma: +11/-1
Offline
Posts: 176
|
|
« Reply #36 on: April 15, 2011, 12:52:42 AM »
|
|
|
@ eliotroyano :
My friend, thank you VERY VERY much for this great find. I will have a look to it, asap
and report back.
Hopefully the author also implements writing of eeproms within time. That would be
really great.
I'm going to test this software asap.
Cheers,
PvL
Hello there any news about dissabling the checksums? |
|
|
|
|
Logged
|
|
|
|
Tony@NefMoto
Administrator
Hero Member
Karma: +132/-4
Offline
Posts: 1389
2001.5 Audi S4 Stage 3
|
|
« Reply #37 on: April 18, 2011, 03:43:24 PM »
|
|
|
Could you specify what kind of thing this is : 'monoscan'
Where you able to read-out the complete content of the eeprom and flashrom ?
The ME7 prevents reading and writing certain regions of the eeprom. Monoscan does not allow you to get at those regions. The regions that can't be read or written include where the immobilizer data is stored. |
|
|
|
|
Logged
|
|
|
|
|
pvl
|
|
« Reply #38 on: April 18, 2011, 03:53:50 PM »
|
|
|
Successfully tested on M3.82 and M3.83 ecu's !
Hope to do a complete log asap, to get a serialnumber from the programmer.
Brilliant software !
Cheers,
PvL
|
|
|
|
|
Logged
|
|
|
|
Dobermann
Full Member
Karma: +7/-0
Offline
Posts: 80
|
|
« Reply #39 on: June 26, 2011, 05:16:13 PM »
|
|
|
hello folks !!!
i tryed to read my ecu eeprom from my seat leon with vag k+can commader
i get the file with 512 byte and the login is to find too
but i think the dump file is not complete or corupted
please have a look on my readed file and tell me what you think !!
i can read and write this file in ecu an car makes no problem
|
|
|
|
|
Logged
|
|
|
|
|
matchew
|
|
« Reply #40 on: June 26, 2011, 05:34:39 PM »
|
|
|
It's not complete
1st line is missing for a start.
|
|
|
|
|
Logged
|
|
|
|
Dobermann
Full Member
Karma: +7/-0
Offline
Posts: 80
|
|
« Reply #41 on: June 26, 2011, 06:54:40 PM »
|
|
|
It's not complete
1st line is missing for a start.
yes that was my thinking too !! i think the start adress is not right !! did someone know the right start adress from the eeprom m95040 ?? i think there is the error !! i read in manual that autodetect muss be deactivatet and the start adress musst set manuel !! |
|
|
|
|
Logged
|
|
|
|
|
gremlin
|
|
« Reply #42 on: June 27, 2011, 05:58:42 AM »
|
|
|
It's not complete
1st line is missing for a start.
Not only first line is missing... There are some lines missing in middle and wrong lines at tail of dump. Because this software read not an EEprom itself but only RAM-mirror part of eeprom. |
|
|
|
|
Logged
|
|
|
|
Dobermann
Full Member
Karma: +7/-0
Offline
Posts: 80
|
|
« Reply #43 on: June 27, 2011, 07:00:53 AM »
|
|
|
It's not complete
1st line is missing for a start.
Not only first line is missing... There are some lines missing in middle and wrong lines at tail of dump. Because this software read not an EEprom itself but only RAM-mirror part of eeprom. yes right ir read part of eeprom !! its not the complete file !! but immo can deactivatet and activatet and the pin code is in the read to find !!! i dont know maybe can the full file be read with the right start adress of eeprom !! i read and write this file in ecu and car start without problems ?? is there a tool that read the full file ( full data) the file sice is ok from my read |
|
|
|
|
Logged
|
|
|
|
carlossus
Sr. Member
Karma: +38/-0
Offline
Posts: 394
Leon Curpa Stg1+
|
|
« Reply #44 on: June 27, 2011, 12:18:39 PM »
|
|
|
I have been around this loop with my own Leon. You can't read the complete EE via OBD2 however you try. Bosch have deliberately disabled that ability on ME7.5. Did you read through here http://nefariousmotorsports.com/forum/index.php/topic,300.0.html ? You *can* read out the SKC which might be good enough, but for Immo defeat you need to physically connect a programmer to the 95040 to read / write. |
|
|
|
|
Logged
|
|
|
|
|
