Pages: [1]
Author Topic: Question about ME7.5 coding 0011711 and 0011581 BEX (swap ecu)  (Read 4703 times)
black
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 80


« on: September 28, 2015, 01:15:24 AM »

Hi,

I know 2 BEX ECUs (8E0909518AS) with different codings on.

0011711 and 0011581...

All BEX should be only manual transmission cars but I get fault codes after swapping BEX ECU 11581 to AVJ 11701 car:

18320 - Pressure sensor for brake boost (G294)- P1912-01- short to plus
18034 - P1626 - (Data bus: missing message from TCU)
17837 - P1429 - Circuit for Brake Vacuum Pump: Open Circuit.

I think the brake codes can be coded out because AVJ has no electric brake booster but the TCU error is maybe VARDEF related?



« Last Edit: October 01, 2015, 12:12:51 AM by black » Logged
black
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 80


« Reply #1 on: July 13, 2016, 10:57:26 PM »

So I got another BEX ECU on my workbench.

This ECU has coding 011511.

In BEX file I can see the codings starting at address 02cb04

02cb10 - 11511
02cb12 - 11711
02vc24 - 11581

11xy1
x=
0 front wheel drive without ASR/ESP  Tongue
2 four wheel drive without ASR/ESP
5 front wheel drive with ASR/ESP  Tongue
7 four wheel drive with ASR/ESP

y=

0 - 5 gear manual
1 - 6 gear manual
5 - 5 gear automatic
8 - multitronic  Roll Eyes




« Last Edit: July 13, 2016, 11:09:31 PM by black » Logged
nubcake
Sr. Member
****

Karma: +53/-4
Offline Offline

Posts: 401


« Reply #2 on: July 14, 2016, 04:08:56 AM »

CWGC, CW_CAN_R, CW_CAN_C
Logged
black
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 80


« Reply #3 on: July 21, 2016, 12:27:50 AM »

CWGC, CW_CAN_R, CW_CAN_C

simply coded via VCDS - no issues anymore
Logged
benni4000
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 24


« Reply #4 on: December 12, 2021, 02:00:38 AM »

Hi,
i've got almost the same problem with my Audi A4 AVJ.
I am flashed 8E0909518G 0261206879 1037396893 but before i did that i set CWGC to 15 and VARDEF to 11501 but i still get P18034 (missing comunication to Transmission(SG)) and my ABS and ESP lights are showing.

No softcodings in VCDS available.
Is there any solution to get this fixed?

Written file is attached.

Regards Benni
Logged
gremlin
Hero Member
*****

Karma: +179/-7
Offline Offline

Posts: 568


« Reply #5 on: December 12, 2021, 06:40:17 AM »


I am flashed 8E0909518G
No softcodings in VCDS available.


This soft is only for cars with multitronic CVT.
Before to flash think what you do.
Logged
benni4000
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 24


« Reply #6 on: December 13, 2021, 12:36:20 PM »

I've found the issue.
CWGC was set to hex 0x15 instead of dec 15.

finally everything is running fine.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.301 seconds with 18 queries. (Pretty URLs adds 0s, 0q)