Launch Control EDC16

Pages: [1] 2

« previous next »

Author

Topic: Launch Control EDC16 (Read 19186 times)

Punda

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 32

	Launch Control EDC16 « on: November 14, 2015, 06:18:12 AM »

Hey Guys

Hope this helps someone but iv found a easier way to do Launch control in the edc16 instead of using the drivers wish maps this method is similar to the edc15 method.

To find the map axis search for a 10x10 map by searching in dec 16bit HiLo
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000

X-axis is speed in Km/h
offset factor 0,010000
0 20 40 60 80 100 120 140 160 180

Y-axis is RPM
00 400 800 1200 1600 2000 2400 2700 3000 5000

Z-axis torque in NM
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000

by looking at the 0 km/h column from 2700rpm to 5000rpm set the torque to 0nm like so (or edit the speed and rpm and torque to your desire)

RPM 0 20 40 60 80 100 120 140 160 180 ----Speed
0 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
400 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
800 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
1200 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
1600 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
2000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
2400 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
2700 0 3000 3000 3000 3000 3000 3000 3000 3000 3000
3000 0 3000 3000 3000 3000 3000 3000 3000 3000 3000
5000 0 3000 3000 3000 3000 3000 3000 3000 3000 3000

In the map pack the map name is "Ersatzwert bei endgültigem CAN Fehler in Abhängigkeit von Eng_nAvrg und VSSCD_v"

Enjoy Grin


	Logged

"The more you learn, the more you realize you don't know."

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #1 on: November 26, 2015, 11:11:04 AM »

There is also another way to make it through the maps relationships V / n and the torque limiter for gear


	Logged

Punda

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 32

	Re: Launch Control EDC16 « Reply #2 on: November 26, 2015, 12:21:46 PM »

Quote from: munro on November 26, 2015, 11:11:04 AM

There is also another way to make it through the maps relationships V / n and the torque limiter for gear

Feel free to add it to this thread. The drivers wish and selector way.


	Logged

"The more you learn, the more you realize you don't know."

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #3 on: November 26, 2015, 12:48:33 PM »

I have no problems to share information on this ECU because here in Italy is widespread but would serve at least one file to be able to watch all the same ..
I tried to upload a tread on but did not succeed.
you can upload?


	Logged

Punda

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 32

	Re: Launch Control EDC16 « Reply #4 on: November 26, 2015, 11:19:06 PM »

Drop me a pm or email and I'll paste it in for you.


	Logged

"The more you learn, the more you realize you don't know."

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #5 on: November 30, 2015, 08:29:07 AM »

ok ... I was able to upload a file
in this file at 0E0FFA find maps of the relationship V / n just bring the top of the first gear ratio to 200 decimal points edit window between the first and second gear 500 points to -500 and change the ratio of the upper second gear also putting in 200 decimal points but then move to the torque limiter for the first march of this file is to 0E11EA and modify it according to how many laps you want the motor vehicle is hung on starting ..
There is also a third way to activate the launch where you change the driver wish for neutral gear which in this file is aa 0D1A3C eliminating completely the map you laps you want to start the launch
punda in this file where the map that you said to activate the launch with your method?


	Logged

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #6 on: November 30, 2015, 08:37:21 AM »

I think I have found an excuse
This file should be posted in the map which stands a 0E1102


	Logged

Punda

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 32

	Re: Launch Control EDC16 « Reply #7 on: November 30, 2015, 10:15:41 AM »

Munro if you could post an example instead of addresses that would help since addresses change from Map to map. Thanks for your contribution.


	Logged

"The more you learn, the more you realize you don't know."

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #8 on: November 30, 2015, 11:07:14 AM »

ok I'll try to post some screenshots ..


	Logged

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #9 on: December 01, 2015, 06:58:40 AM »

as promised attach these 2 Screen launch control on edc16u1 in the first you can see the changes to the relationship V / n in the second screen you can see the change of the torque limiter for the first gear just ... I can also place the launch via driver wish ...


	Logged

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #10 on: December 01, 2015, 07:00:54 AM »

ooops I attached only the second screen ... here it is the first


	Logged

vwaudiguy

Hero Member

Karma: +53/-37
Offline

Offline

Posts: 2024

	Re: Launch Control EDC16 « Reply #11 on: December 01, 2015, 02:23:47 PM »

Does anyone know the FR name of this map?


	Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."

munro

Jr. Member

Karma: +0/-0
Offline

Offline

Posts: 33

	Re: Launch Control EDC16 « Reply #12 on: December 01, 2015, 02:32:22 PM »

obere Grenze des v/n-Toleranzbandes Gang


« Last Edit: December 01, 2015, 02:36:03 PM by munro »	Logged

vwaudiguy

Hero Member

Karma: +53/-37
Offline

Offline

Posts: 2024

	Re: Launch Control EDC16 « Reply #13 on: December 01, 2015, 03:55:53 PM »

Quote from: munro on December 01, 2015, 02:32:22 PM

obere Grenze des v/n-Toleranzbandes Gang

Thanks


	Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."

jawier130

Newbie

Karma: +0/-0
Offline

Offline

Posts: 4

	Re: Launch Control EDC16 « Reply #14 on: March 08, 2017, 05:24:25 AM »

I have try it on EDC16U (VW Touareg) but not work


	Logged

Pages: [1] 2

« previous next »

Jump to:

Navigation

Personal Tools

November 27, 2024, 04:13:13 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search