Pages: [1]
Author Topic: Re: Massive timing retardation + low power  (Read 4134 times)
BlkSerialKilla
Full Member
***

Karma: +18/-0
Offline Offline

Posts: 106


That's Just The Nature Of The Beast...


« on: November 14, 2015, 06:03:53 PM »

Not to thread jack but is it possible my MAF is going bad? I'm feeling my timing correction is possibly due to it. I have a log and pictures bellow.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #1 on: November 14, 2015, 06:42:07 PM »

If you can't make 12psi with 100% dc you have other problems
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640


« Reply #2 on: November 14, 2015, 06:47:39 PM »

Also, maybe look at how many knock events you have. 7.5 degrees of timing being pulled is not massive. That will likely only take 1.5 degrees pulled to eliminate entirely.....
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #3 on: November 14, 2015, 08:33:22 PM »

That will likely only take 1.5 degrees pulled to eliminate entirely.....

I'm not sure if that statement is application-specific for this particular engine/setup, but I've never seen a case where I had 7-8 deg of timing pull, and only 1.5 taken from the table was enough to resolve it. I'm sure I'm missing something somewhere.
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Lost
Hero Member
*****

Karma: +21/-14
Offline Offline

Posts: 556


« Reply #4 on: November 15, 2015, 01:07:28 AM »

It will. It's the same the other way around.
0.75 to much can couse 3 - 4.5 deg retard.
Logged
BlkSerialKilla
Full Member
***

Karma: +18/-0
Offline Offline

Posts: 106


That's Just The Nature Of The Beast...


« Reply #5 on: November 15, 2015, 08:06:13 AM »

If you can't make 12psi with 100% dc you have other problems

I agree, I've been attempting to resolve that issue and right now everything is pointing to the wastegate going south unfortunate for me.  I've tried boost leak test and have corrected everything else I could find. So I'm hunting a good k04 or F21. I'm at 172k miles is this to be expected around this mileage? I've been experiencing this issue since 160k.

Also, maybe look at how many knock events you have. 7.5 degrees of timing being pulled is not massive. That will likely only take 1.5 degrees pulled to eliminate entirely.....

I'm going to do a new log supplementing zkrvf_0-3 and report back.




Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #6 on: November 15, 2015, 11:47:59 AM »

I'm going to do a new log supplementing zkrvf_0-3 and report back

There's not much point in wasting time tweaking bad hardware. Get your HW problems sorted first, then tune.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 16 queries. (Pretty URLs adds 0s, 0q)