Mythbuster74
Full Member
Karma: +0/-0
 Offline
Posts: 84
|
 |
« on: March 06, 2016, 12:51:11 PM »
|
|
|
I need to get my brothers car through emissions (018ch awm a4), so up until now I've just disabled the sai through the eskonf but I don't believe it'll pass this way. After looking around a little I think I've found it but I've never been very good/fully understood how to find maps and use the offsets and axis data.
I believe I've found it at 1AC2E and its an 8x1 16bit map. With values 6400 7936 9280 10752 13312 14592 15872 17024 without adding any axis data or units. Is this correct?
I've attached a older version of 018ch file on it now
|
|
|
|
|
Logged
|
|
|
|
Mythbuster74
Full Member
Karma: +0/-0
Offline
Posts: 84
|
|
« Reply #1 on: March 08, 2016, 12:48:25 PM »
|
|
|
Hello... It's me.... I was wondering if after all this time you'd found... Lol
Can anyone help?
|
|
|
|
|
Logged
|
|
|
|
Mythbuster74
Full Member
Karma: +0/-0
Offline
Posts: 84
|
|
« Reply #2 on: March 09, 2016, 10:07:03 AM »
|
|
|
Nyet? DDillinger? Other forum God's?
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #3 on: March 09, 2016, 10:57:46 AM »
|
|
|
0x1AC2E is the start of the map.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
funnix
Full Member
Karma: +1/-0
Offline
Posts: 76
1.8t AUM
|
|
« Reply #4 on: June 14, 2016, 01:39:34 AM »
|
|
|
Hey guys,
i am looking for MSLUB maplocation in 032DR_0002. Can anyone help?
|
|
|
|
|
Logged
|
|
|
|
Mythbuster74
Full Member
Karma: +0/-0
Offline
Posts: 84
|
|
« Reply #5 on: September 03, 2016, 09:15:58 AM »
|
|
|
0x1AC2E is the start of the map.
Could you also help me find MSLBAS? The single digit maps are always tricky. Zeroing MSLUB wasn't enough to set readiness or solve the no high idle issues. |
|
|
|
|
Logged
|
|
|
|
Mythbuster74
Full Member
Karma: +0/-0
Offline
Posts: 84
|
|
« Reply #6 on: September 08, 2016, 02:54:04 PM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #7 on: September 08, 2016, 03:44:44 PM »
|
|
|
Try 0x18381
|
|
|
|
« Last Edit: September 08, 2016, 03:48:40 PM by vwaudiguy »
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
vdubnation
Turboman
Global Moderator
Sr. Member
Karma: +49/-2
Offline
Posts: 433
|
|
« Reply #8 on: September 09, 2016, 07:39:18 PM »
|
|
|
hes right
|
|
|
|
|
Logged
|
|
|
|
|
mister t
|
|
« Reply #9 on: September 10, 2016, 01:17:01 PM »
|
|
|
Nyet? DDillinger? Other forum God's?
[/quote
I'll amend this post to state: "Nyet?, DDillinger (in shimmering Jedi robed guise a la Obi Wan), God....? |
|
|
|
|
Logged
|
|
|
|
Mythbuster74
Full Member
Karma: +0/-0
Offline
Posts: 84
|
|
« Reply #10 on: September 13, 2016, 08:38:44 AM »
|
|
|
I've set the mslub map and the mslbas maps both to 0 for all values, but the car still doesn't idle up or set readiness. There's a resistor in the sai pump plug, and it's still turned on in the eskonf. Am I missing something?
|
|
|
|
|
Logged
|
|
|
|
Mythbuster74
Full Member
Karma: +0/-0
Offline
Posts: 84
|
|
« Reply #11 on: September 13, 2016, 08:41:36 AM »
|
|
|
Looked at the wiki again and it said to unplug the pump, so I'll take out the resistor and report back.
|
|
|
|
|
Logged
|
|
|
|
|
