Pages: [1]
Author Topic: What would be considered high IAT?  (Read 8252 times)
marcello7x
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 126


« on: July 13, 2012, 05:23:27 PM »

Im curious what is considered a high intake air temp?
Logged
userpike
Hero Member
*****

Karma: +22/-1
Offline Offline

Posts: 763


« Reply #1 on: August 04, 2012, 01:50:18 PM »

Im curious what is considered a high intake air temp?
me too...I want to tune for my FMIC....
Logged
sn00k
Sr. Member
****

Karma: +59/-2
Offline Offline

Posts: 277


« Reply #2 on: August 04, 2012, 06:13:52 PM »

well.. lower is generally better.. but i would say 25-30 deg above ambient air would be to consider HIGH.  Smiley
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #3 on: August 07, 2012, 10:34:46 AM »

I would say if IAT has the munchies or is extremely relaxed it is probably high.
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
userpike
Hero Member
*****

Karma: +22/-1
Offline Offline

Posts: 763


« Reply #4 on: August 07, 2012, 12:33:00 PM »

I would say if IAT has the munchies or is extremely relaxed it is probably high.

I have the munchies and am extremly relaxed right now..
Logged
prj
Hero Member
*****

Karma: +1072/-485
Offline Offline

Posts: 6040


« Reply #5 on: August 08, 2012, 06:42:48 AM »

Do a full third gear pull from 2000 to 7000 RPM at WOT.
Note the lowest and the highest IAT. This will be your delta.

If your delta exceeds 20 degrees, you are probably running too much boost.
As a rule of thumb you want it between 15 and 20 degrees tops.

I will probably get flamed to hell for this post, but perhaps it'll help someone.
Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
20VTMK1
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 113


« Reply #6 on: August 22, 2012, 03:25:37 AM »

Also , the approach temp (diff between ambient and cooler exit temp) must not be more than 20 deg C - that considered poor cooling if it's higher. Trying to get less than 20 is the law of diminishing returns as you need substantially larger area , however this causes other problems.

Good rule of thumb advice I think , WMI would assist in bringing the approach temps down further , however WMI is a band aid and not a cure
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #7 on: August 22, 2012, 09:35:12 AM »

I'd also make sure that on really hot days, you aren't pulling to much timing due to elevated IATs. If you are, and bigger intercoolers don't help (they often don't), then WMI or pulling boost is all you can do.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
marcello7x
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 126


« Reply #8 on: September 25, 2012, 10:27:32 AM »

Thanks for all the help guys, i didn't have a chance to get back on the forum for a while.

My issue was def high ambient 96*f+, and trying to tune for high boost W/ a tiny inter-cooler. Bigger inter-cooler and wmi was a bandaid, but i pulled some more timing and held off on increasing the boost till recently where temps have dropped here in new England.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)