NefMoto > Technical > Tuning > Converting: Stage1 1.8t ME7.5 A4 (8E0909518AK-0003) over to 4B0906018CM
Pages: [1]
« previous next »
Author Topic: Converting: Stage1 1.8t ME7.5 A4 (8E0909518AK-0003) over to 4B0906018CM  (Read 7213 times)
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
Could anyone give me a general idea on how much work it would be to convert the Stage1 1.8t ME7.5 A4 (8E0909518AK-0003) over to 1.8t ME7.5 Passat (4B0906018CM) ?
Logged
Tuning Wiki
Jerry Tunin
panos1975
Full Member
***

Karma: +7/-6
Offline Offline

Posts: 105
« Reply #1 on: December 05, 2014, 12:08:19 PM »
not enough if you know the basics......tunerpro or winols software,find which maps are modified in 8E0 and transfer them to the 4B0......if you need help ask here on forum,everyone here is very helpful......
Logged
thelastleroy
Sr. Member
****

Karma: +19/-2
Offline Offline

Posts: 260
« Reply #2 on: December 05, 2014, 02:25:15 PM »
You'll need a definition file (.xdf) for your software (4B0906018CM). The definition file needs to have the same maps in it that the community file used. Alternately you may be able to cross flash your ecu with another bin file which already has a good definition file to match. I'm not sure which file would work on yours myself,  but someone else might know.
Logged
ddillenger
Hero Member
*****

Karma: +640/-21
Offline Offline

Posts: 5640
« Reply #3 on: December 05, 2014, 02:39:29 PM »
018CH will crossflash!
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
MadCow
Full Member
***

Karma: +3/-1
Offline Offline

Posts: 108
« Reply #4 on: December 05, 2014, 02:55:32 PM »
I've ported it to a CH bin, it's far from complete but it's a start. I used this bin (SW 360101) as a base.  I can post it if you want, but be aware that it'll still need a good amount of fine tuning. The only difference I've found so far between the AK and CH is ZKLAMFAW is a map in AK and a single variable in CH.
Logged
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
« Reply #5 on: December 08, 2014, 01:18:35 PM »
Quote from: MadCow on December 05, 2014, 02:55:32 PM
I've ported it to a CH bin, it's far from complete but it's a start. I used this bin (SW 360101) as a base.  I can post it if you want, but be aware that it'll still need a good amount of fine tuning. The only difference I've found so far between the AK and CH is ZKLAMFAW is a map in AK and a single variable in CH.

Yes, please post and I'll take a look at it and see what I can contribute.
Logged
Tuning Wiki
Jerry Tunin
MadCow
Full Member
***

Karma: +3/-1
Offline Offline

Posts: 108
« Reply #6 on: December 08, 2014, 05:19:27 PM »
Here it is, I tried to remove all the changes I made specifically for my car like emissions deletes and stuff but I might not have gotten it all. Again check it over before you flash.
Logged
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
« Reply #7 on: December 19, 2014, 01:32:00 PM »
Quote from: MadCow on December 08, 2014, 05:19:27 PM
Here it is, I tried to remove all the changes I made specifically for my car like emissions deletes and stuff but I might not have gotten it all. Again check it over before you flash.

Would you be able to post the one with your changes?  Also, do you know or would you be able to list the changes you made?  I don't have a CAT so far but I may be removing additional items as well.
Logged
Tuning Wiki
Jerry Tunin
MadCow
Full Member
***

Karma: +3/-1
Offline Offline

Posts: 108
« Reply #8 on: December 19, 2014, 03:01:00 PM »
Everything I did can be easily found on these forums, I'm going off memory right now but I believe it was: cat, sai, a few canbus-related DTCs removed, and dwell times changed for TFSI coils. Just make the changes yourself, it's not hard at all. If you can't do that then you shouldn't be messing with your the bin yourself anyway.
Logged
TLS
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 62
« Reply #9 on: February 08, 2015, 11:25:37 PM »
I know this is a hijack, but similar theory.

My Bin is 4B0906018AC 0003 400BB
Are you saying that I can load the stock 018CH bin on there and that would be a good start because the ols/kp is well defined for that one?

I wasn't sure if DDilinger meant that the 518AK file will port to the 018CH, or whether his CM will port to CH.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • September 13, 2024, 08:54:58 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.039 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)