|
vwaudiguy
|
 |
« Reply #30 on: November 02, 2011, 11:21:14 AM »
|
|
|
^^Very true, plus no tight radius turning..
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
ejg3855
Full Member
Karma: +6/-0
 Offline
Posts: 123
|
|
« Reply #31 on: November 07, 2011, 06:57:44 AM »
|
|
|
did that bench harness ever get built for this?
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #32 on: November 07, 2011, 01:30:12 PM »
|
|
|
Ready to go!
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
ejg3855
Full Member
Karma: +6/-0
Offline
Posts: 123
|
|
« Reply #33 on: November 08, 2011, 07:19:53 AM »
|
|
|
so you can pull the raw data off the IC?
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #34 on: November 11, 2011, 01:41:34 PM »
|
|
|
No, I just have a bench harness made. I have no idea what program to use, and whether it is read over the k line or can bus.
|
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
ejg3855
Full Member
Karma: +6/-0
Offline
Posts: 123
|
|
« Reply #35 on: November 22, 2011, 11:56:00 AM »
|
|
|
Thats where my knowledge lacks too, how to get the data off the chip.
Maybe someone can shine some light.
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #36 on: November 22, 2011, 11:59:37 AM »
|
|
|
AZIZ! LIGHT!  |
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
|
Gonzo
|
|
« Reply #37 on: November 22, 2011, 09:50:46 PM »
|
|
|
You need to know what address to connect to and then have nefmoto try to connect there and see what the module supports.
|
|
|
|
|
Logged
|
|
|
|
carlossus
Sr. Member
Karma: +38/-0
Offline
Posts: 394
Leon Curpa Stg1+
|
|
« Reply #38 on: November 23, 2011, 12:24:03 AM »
|
|
|
Or try Monoscan.
|
|
|
|
|
Logged
|
|
|
|
|
Gonzo
|
|
« Reply #39 on: November 23, 2011, 10:11:26 AM »
|
|
|
Or try Monoscan.
Great idea! |
|
|
|
|
Logged
|
|
|
|
ArgDub
Full Member
Karma: +60/-1
Offline
Posts: 202
|
|
« Reply #40 on: November 23, 2011, 08:57:20 PM »
|
|
|
It uses a c167 uP, right? can you reset the controller in bootmode  |
|
|
|
|
Logged
|
|
|
|
ejg3855
Full Member
Karma: +6/-0
Offline
Posts: 123
|
|
« Reply #41 on: November 24, 2011, 09:58:01 AM »
|
|
|
It uses a c167 uP, right? can you reset the controller in bootmode I looked up that C167 and all the data sheets show a bunch more pins that we see. Maybe I am silly. |
|
|
|
|
Logged
|
|
|
|
ArgDub
Full Member
Karma: +60/-1
Offline
Posts: 202
|
|
« Reply #42 on: November 24, 2011, 10:38:12 AM »
|
|
|
I guess that pin is hard to find.. I know its a lot of work, but you can try pin by pin with a 4k7 resistor.
|
|
|
|
« Last Edit: November 24, 2011, 10:40:34 AM by ArgDub »
|
Logged
|
|
|
|
Swat Cat
Newbie
Karma: +2/-0
Offline
Posts: 8
|
|
« Reply #43 on: November 25, 2011, 12:27:12 AM »
|
|
|
soo.... not controller.... not haldex flashing.....
|
|
|
|
|
Logged
|
|
|
|
terok
Full Member
Karma: +8/-3
Offline
Posts: 134
|
|
« Reply #44 on: December 02, 2011, 01:11:25 PM »
|
|
|
Gen2 fairly easy to read&write outside of the car. Are there any tools available that support flashing of gen2 via CAN?
Gen1 seems a bit more tricky.
|
|
|
|
|
Logged
|
|
|
|
|
