Haldex Controllers Thinking.....

Pages: 1 ... 16 17 [18] 19 20 ... 29

« previous next »

Author

Topic: Haldex Controllers Thinking..... (Read 276210 times)

dream3R

Hero Member

Karma: +18/-8
Offline

Offline

Posts: 1194

	Re: Haldex Controllers Thinking..... « Reply #255 on: January 15, 2016, 09:35:34 PM »

5 baud init rings a bell


	Logged

How to work out values from an A2L

http://nefariousmotorsports.com/forum/index.php?topic=5525.msg52371#msg52371

Starting Rev's http://nefariousmotorsports.com/forum/index.php?topic=5397.msg51169#msg51169

noobs read this before asking http://nefariousmotorsports.com/forum/index.php?topic=9014.0title=

ORGORIGINAL 05 5120 creator for Volvo
ORIGINAL Datalogger (Freeware) Author
ORGINAL finder of the 'extra' torque' limits
I don't have ME7.01 A2L I just use ID

ccyberwing

Newbie

Karma: +7/-0
Offline

Offline

Posts: 19

	Re: Haldex Controllers Thinking..... « Reply #256 on: January 16, 2016, 07:16:36 AM »

Finally i made a picture, how to read the haldex controller via bootmode and kline (yes, i love paint Cool

)

I know there are more versions of this controller in the field, please send me an hires picture and i will
make the modifications necessary to connect via bootmode.

I hope my picture is not too confusing Cheesy

regards

https://dropmefiles.com/krMDu


« Last Edit: January 16, 2016, 07:38:16 AM by ccyberwing »	Logged

fknbrkn

Hero Member

Karma: +185/-23
Offline

Offline

Posts: 1454

mk4 1.8T AUM

	Re: Haldex Controllers Thinking..... « Reply #257 on: January 16, 2016, 07:35:02 AM »

https://dropmefiles.com/


	Logged

ccyberwing

Newbie

Karma: +7/-0
Offline

Offline

Posts: 19

	Re: Haldex Controllers Thinking..... « Reply #258 on: January 16, 2016, 07:37:22 AM »

Quote from: fukenbroken on January 16, 2016, 07:35:02 AM

https://dropmefiles.com/

nice, thanks! - updated the upper post


	Logged

fknbrkn

Hero Member

Karma: +185/-23
Offline

Offline

Posts: 1454

mk4 1.8T AUM

	Re: Haldex Controllers Thinking..... « Reply #259 on: January 16, 2016, 07:51:01 AM »

Quote from: ccyberwing on January 16, 2016, 07:37:22 AM

nice, thanks! - updated the upper post

wow thats make a sense
do you have a pinout for that +12v/kline/gnd port?
which software you are using?
is it possible to write flash back?


	Logged

Full Member

Karma: +20/-1
Offline

Offline

Posts: 184

	Re: Haldex Controllers Thinking..... « Reply #260 on: January 16, 2016, 07:53:59 AM »

Incredible. Thank you!
Though more than expected that needs to be connected and therefore much more difficult to achieve. Do you have a live picture of how you did it?

Is there no need to control direction of kline? In flash code it looks like P2_14 must be set or cleared to controle receive or transmit.
Or is that what you've somehow done with the connection of mcu and transciever?


	Logged

Try ME7idatool http://nefariousmotorsports.com/forum/index.php?topic=21130.0

ccyberwing

Newbie

Karma: +7/-0
Offline

Offline

Posts: 19

	Re: Haldex Controllers Thinking..... « Reply #261 on: January 16, 2016, 07:58:05 AM »

use the original power plug from the haldex controller. (you need the capacitor in the plug)

black 8 pin connector from haldex:

Pin 1 = +12V
Pin 2 = Ground
Pin 5 = K-Line

i use an self written application for boot mode and modified flash drivers.
but minimon should work too, but i havent tried.

yes, possible to flash back - tried many times Grin


	Logged

Full Member

Karma: +20/-1
Offline

Offline

Posts: 184

	Re: Haldex Controllers Thinking..... « Reply #262 on: January 16, 2016, 08:02:33 AM »

without Haldex cable

I've only done vcds through these pins and need to test to attach a correct capacitor.


	Logged

Try ME7idatool http://nefariousmotorsports.com/forum/index.php?topic=21130.0

ccyberwing

Newbie

Karma: +7/-0
Offline

Offline

Posts: 19

	Re: Haldex Controllers Thinking..... « Reply #263 on: January 16, 2016, 08:07:16 AM »

Quote from: DT on January 16, 2016, 07:53:59 AM

no problem, i am happy if i can help

and i think nefmoto is a nice community.

i was most surprised about the pol0.4 connection, why its on the header.

i can make a picture in action, i soldered wires on the hybrid - a bit fuzzy, but its possible.
later i used test pins (spring loaded needles) to connect.

hmm, could be - i havent analysed this part of software yet.
the connection is there because i haven't found any route between asc0.txd and the input of the k-line transceiver.


« Last Edit: January 16, 2016, 08:12:15 AM by ccyberwing »	Logged

ccyberwing

Newbie

Karma: +7/-0
Offline

Offline

Posts: 19

	Re: Haldex Controllers Thinking..... « Reply #264 on: January 16, 2016, 08:08:35 AM »

Quote from: DT on January 16, 2016, 08:02:33 AM

without Haldex cable

I've only done vcds through these pins and need to test to attach a correct capacitor.

you need only some µF. about 100µF to 470µF should do.


	Logged

Full Member

Karma: +20/-1
Offline

Offline

Posts: 184

	Re: Haldex Controllers Thinking..... « Reply #265 on: January 16, 2016, 08:11:08 AM »

ok, well then I don't even have to look for the cable. I've got many standard caps like that.

I find it a bit confusing that they've made the P0L.4 available at connector if it's not supposed to be possible to work without connections directly at circuit board.
(suprised just like you :-) )


	Logged

Try ME7idatool http://nefariousmotorsports.com/forum/index.php?topic=21130.0

Full Member

Karma: +20/-1
Offline

Offline

Posts: 184

	Re: Haldex Controllers Thinking..... « Reply #266 on: January 16, 2016, 08:18:36 AM »

Quote from: ccyberwing on January 16, 2016, 08:07:16 AM

hmm, could be - i havent analysed this part of software yet.
the connection is there because i haven't found any route between asc0.txd and the input of the k-line transceiver.

Well there is connection since all communication go through S0TBUF and S0RBUF (hance ASC0) but they also have the P2_14 connected to the transciever to control in/out from the transciever.

They do a bclr P2_14 before every load of TBUF and a bset p2_14 directly after Transmit interrupt to be ready to receive again.


	Logged

Try ME7idatool http://nefariousmotorsports.com/forum/index.php?topic=21130.0

ccyberwing

Newbie

Karma: +7/-0
Offline

Offline

Posts: 19

	Re: Haldex Controllers Thinking..... « Reply #267 on: January 16, 2016, 08:22:28 AM »

Quote from: DT on January 16, 2016, 08:18:36 AM

ahh, that makes sense - its not the mcu txd - its the transceiver CS ... lol


	Logged

Full Member

Karma: +20/-1
Offline

Offline

Posts: 184

	Re: Haldex Controllers Thinking..... « Reply #268 on: January 16, 2016, 08:24:45 AM »

Haha, yes txd could ofcourse control the CS :-)

The problem is that I don't know for sure if receive status of transciever is default. It probably is and then it is possible to inject the 32bit load code at correct time after reset without boot mode confirmation sent from ecu. I have modified the minimonK code to control P2_14 when executed.


	Logged

Try ME7idatool http://nefariousmotorsports.com/forum/index.php?topic=21130.0

ccyberwing

Newbie

Karma: +7/-0
Offline

Offline

Posts: 19

	Re: Haldex Controllers Thinking..... « Reply #269 on: January 16, 2016, 08:28:04 AM »

Quote from: DT on January 16, 2016, 08:24:45 AM

Yes, default is receive - confirmed.

would be good - so we only need to figure out how to disable the reset watchdog


	Logged

Pages: 1 ... 16 17 [18] 19 20 ... 29

« previous next »

Jump to:

Navigation

Personal Tools

November 22, 2024, 10:39:01 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search