|
k0mpresd
|
 |
« Reply #285 on: January 21, 2016, 07:08:34 PM »
|
|
|
ive been holding on to these controllers for a while.
i have 2 gen2 and 2 gen4.
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #286 on: January 21, 2016, 07:17:57 PM »
|
|
|
ive been holding on to these controllers for a while.
You can set them down on the table for a bit. Your hands must be killing you. |
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
|
k0mpresd
|
|
« Reply #287 on: January 22, 2016, 11:30:39 PM »
|
|
|
with resistor marked in orange still attached to board, vcds connects no matter if ground wire (1k resistor) connected or not. video is with resistor removed. i assume this is bootmode. http://youtu.be/AgrpIf2hlV0high res image: http://www.filedropper.com/2ee |
|
|
|
« Last Edit: January 22, 2016, 11:44:08 PM by k0mpresd »
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #288 on: January 23, 2016, 09:17:35 AM »
|
|
|
Thanks for taking the time dude. Get minimon cracked out  |
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #289 on: January 23, 2016, 12:38:09 PM »
|
|
|
connected to haldex via TTL converter + 1k boot pin, resistor still removed from circuit. Tx/Rx in green and yellow. minimon screenshot attached. no c167cs-lm option in minimon so using all default c167cr options. serial connection: http://www.filedropper.com/serial_5 |
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #290 on: January 23, 2016, 01:06:39 PM »
|
|
|
ok, so after a few attempts of powering on/off and trying to connect with minimon, 1 time it completely connected and another it would lose connection and attempt to reconnect during loading but said connection lost in the end.
technically, i guess it works. sort of.
|
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #291 on: January 23, 2016, 01:10:55 PM »
|
|
|
bootmode connected.  edit: this seems to be easily repeated with p0l.4 connected directly to ground, no 1k ohm. k-line does not seem to be connected to pin 5 on haldex connector. no type of reply from minimon with a kkl cable. boot log: *Loader file Prepare
*Minimon file Prepare
*send Byte 0+ Loader + MinimonCore
*RECEIVE - MC-Identifier: D5
*RECEIVE - LoaderACK 01 received
*RECEIVE - Minimon ACK 03 received
*Minimon successfully launched
*Reset: BUSCON0=0680
*Reset: SYSCON=0400
*Reset Configuration: External Bus enabled
*Reset Configuration: 16 Bit demultiplexed Bus
*Reset Configuration: WR# and BHE# retain their normal function (P0H.0=0)
*Reset Configuration: On chip watchdog timer is disabled (RD#=0)
*Reset Configuration: Lengthened ALE signal
*Initialisation: Write to SYSCON
*ERROR: Minimon Acknowledge not Received
*Initialisation: Write to BUSCON0
*Initialisation: Write to BUSCON1
*Initialisation: Write to ADDRSEL1
*Initialisation: Write to BUSCON2
*Initialisation: Write to ADDRSEL2
*Initialisation: Write to BUSCON3
*Initialisation: Write to ADDRSEL3
*Initialisation: Write to BUSCON4
*Initialisation: Write to ADDRSEL4
*Initialisation: Enable X-Peripherals via SYSCON
*Initialisation: Call EINIT Command
|
|
|
|
« Last Edit: January 23, 2016, 01:33:29 PM by k0mpresd »
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #292 on: January 23, 2016, 02:55:28 PM »
|
|
|
Try a 120r instead, nice work guys props.
|
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #293 on: January 23, 2016, 05:27:59 PM »
|
|
|
st10f272m gen4, bootmode!! *Loader file Prepare
*Minimon file Prepare
*send Byte 0+ Loader + MinimonCore
*RECEIVE - MC-Identifier: D5
*RECEIVE - LoaderACK 01 received
*RECEIVE - Minimon ACK 03 received
*Minimon successfully launched
*Reset: BUSCON0=0280
*Reset: SYSCON=0600
*Reset Configuration: External Bus disabled
*Reset Configuration: 16 Bit demultiplexed Bus
*Reset Configuration: WR# and BHE# retain their normal function (P0H.0=0)
*Reset Configuration: On chip watchdog timer is disabled (RD#=0)
*Reset Configuration: Lengthened ALE signal
*Initialisation: Write to SYSCON
03 *ERROR: Minimon Acknowledge not Received
*Initialisation: Write to BUSCON0
*Initialisation: Write to BUSCON1
*Initialisation: Write to ADDRSEL1
*Initialisation: Write to BUSCON2
*Initialisation: Write to ADDRSEL2
*Initialisation: Write to BUSCON3
*Initialisation: Write to ADDRSEL3
*Initialisation: Write to BUSCON4
*Initialisation: Write to ADDRSEL4
*Initialisation: Enable X-Peripherals via SYSCON
*Initialisation: Call EINIT Command
|
|
|
|
|
Logged
|
|
|
|
|
vwaudiguy
|
|
« Reply #294 on: January 23, 2016, 05:33:23 PM »
|
|
|
st10f272m gen4, bootmode!! *Loader file Prepare
*Minimon file Prepare
*send Byte 0+ Loader + MinimonCore
*RECEIVE - MC-Identifier: D5
*RECEIVE - LoaderACK 01 received
*RECEIVE - Minimon ACK 03 received
*Minimon successfully launched
*Reset: BUSCON0=0280
*Reset: SYSCON=0600
*Reset Configuration: External Bus disabled
*Reset Configuration: 16 Bit demultiplexed Bus
*Reset Configuration: WR# and BHE# retain their normal function (P0H.0=0)
*Reset Configuration: On chip watchdog timer is disabled (RD#=0)
*Reset Configuration: Lengthened ALE signal
*Initialisation: Write to SYSCON
03 *ERROR: Minimon Acknowledge not Received
*Initialisation: Write to BUSCON0
*Initialisation: Write to BUSCON1
*Initialisation: Write to ADDRSEL1
*Initialisation: Write to BUSCON2
*Initialisation: Write to ADDRSEL2
*Initialisation: Write to BUSCON3
*Initialisation: Write to ADDRSEL3
*Initialisation: Write to BUSCON4
*Initialisation: Write to ADDRSEL4
*Initialisation: Enable X-Peripherals via SYSCON
*Initialisation: Call EINIT Command
w00t! |
|
|
|
|
Logged
|
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
|
|
|
|
k0mpresd
|
|
« Reply #295 on: January 23, 2016, 08:21:10 PM »
|
|
|
does anyone know of any software that will read/write st10 cpu?
i tried st10flasher 2.4b, but it says the 0xD5 ID is wrong even though it seems to be correct for minimon, the 1 time it actually ID'd correct. normally says BSL mode failed to start.
cpu has on board 256kb. k-line doesnt seem to be connected on this controller either.
id like to test by running a k-line jumper as described in ccyberwing's diagram but not which pins to jump.
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #296 on: January 23, 2016, 08:23:39 PM »
|
|
|
does anyone know of any software that will read/write st10 cpu?
i tried st10flasher 2.4b, but it says the 0xD5 ID is wrong even though it seems to be correct for minimon, the 1 time it actually ID'd correct. normally says BSL mode failed to start.
cpu has on board 256kb. k-line doesnt seem to be connected on this controller either.
id like to test by running a k-line jumper as described in ccyberwing's diagram but not which pins to jump.
I'll send you my IO terminal. |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
|
dream3R
|
|
« Reply #297 on: January 23, 2016, 10:10:44 PM »
|
|
|
Re resistors and pol4 iirc you need really yo use one or or could be bye bye.
It's all about circuit impedance and ohms law and also Kirchhoffs Law iirc1 blah.
Uoto you though.
Some datasheet say 10k sone 8k those laws are the reason.
For that I'd use a 120r
|
|
|
|
|
Logged
|
|
|
|
|
|
|
dream3R
|
|
« Reply #299 on: January 24, 2016, 10:46:29 AM »
|
|
|
Of course as there is no voltage drop across the resistor as there isn't one. I'll give my Volvo Gen2 one a try when I find it lol |
|
|
|
|
Logged
|
|
|
|
|
