|
birchbark506
|
 |
« on: August 04, 2016, 04:43:29 PM »
|
|
|
I have a unitronics stage 1+ ecu and I want to know how to read the EPROM on a med 9.1 ecu with a bdm100 clone can't seem to get it to connect I know they lock it so you can't read or write over obd2
|
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #1 on: August 04, 2016, 05:06:55 PM »
|
|
|
bdm port could be fried, clone might no support it, list goes on......EVC are still are adding updates to theirs iirc
Where u based?
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #2 on: August 04, 2016, 05:58:44 PM »
|
|
|
I'm in Canada, and I don't think it be cooked as the ecu still worked in the car, two bdm100 and both the same error
|
|
|
|
|
Logged
|
|
|
|
|
dream3R
|
|
« Reply #3 on: August 04, 2016, 06:02:23 PM »
|
|
|
no idea sorry.
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #4 on: July 26, 2017, 08:33:53 AM »
|
|
|
little update for everyone i haven't been active in a while but i pulled out my BDM 100 Clone today to try this extra ECU i picked up over the winter from the junk yard well i finally had luck at getting it to work and i think i pulled the .e2p file and the .bin off the ECU correctly this is the first time i had one of the 2 clones i had to work, i guess the first adptor i made with the pins was a dead so i finallly got the pins installed in my new adptor here are the files i pulled off this ECU can someone tell me if i did it right.
|
|
|
|
|
Logged
|
|
|
|
|
SB_GLI
|
|
« Reply #5 on: July 26, 2017, 12:13:58 PM »
|
|
|
it is against the forum rules to post commercial files
|
|
|
|
|
Logged
|
|
|
|
Beaviz
Full Member
Karma: +8/-4
 Offline
Posts: 190
|
|
« Reply #6 on: July 27, 2017, 12:58:16 AM »
|
|
|
Files look fine. None of them look commercial to me.
|
|
|
|
|
Logged
|
|
|
|
|
IamwhoIam
|
|
« Reply #7 on: July 27, 2017, 06:06:30 AM »
|
|
|
That junk sure doesn't look like anything unitronic to me
|
|
|
|
|
Logged
|
I have no logs because I have a boost gauge (makes things easier)
|
|
|
|
SB_GLI
|
|
« Reply #8 on: July 27, 2017, 09:13:00 AM »
|
|
|
That junk sure doesn't look like anything unitronic to me
Good deal, I just assumed based on thread title. I didn't look at the file myself. Carry on. |
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #9 on: July 28, 2017, 06:01:22 AM »
|
|
|
this was an old post i did from last year, i end up messing the BDM ports on that unitronics flash ECU and threw it out, i also had other ecu i end up bricking last year and could not get my BDM to work and then just replaced it with other ECU that was already IMMO off, the files i posted are all stock and not the unitronics flash. the files i posted are off my extra ECU that i just got my BDM to read and wanted to make sure i did it correct.
Thank you all for your help
|
|
|
|
|
Logged
|
|
|
|
|
IamwhoIam
|
|
« Reply #10 on: July 29, 2017, 09:49:11 AM »
|
|
|
The files from your extra ECU are a shit tune
|
|
|
|
|
Logged
|
I have no logs because I have a boost gauge (makes things easier)
|
|
|
|
birchbark506
|
|
« Reply #11 on: July 29, 2017, 11:59:53 AM »
|
|
|
Oh Yes I know it was from my bricked ECU I end up flashing wrong file when not paying attention, I just wanted to make sure that I used the BDM proper.  This files are no Good |
|
|
|
|
Logged
|
|
|
|
focalpoint519
Full Member
Karma: +29/-65
Offline
Posts: 148
|
|
« Reply #12 on: August 02, 2017, 12:07:58 AM »
|
|
|
Check for missing resistors.... look close at a OEM ecu then the Unitronics one, usually close to the memory chip SMD resistor may be missing, therefor blocking reading.
|
|
|
|
|
Logged
|
|
|
|
|
birchbark506
|
|
« Reply #13 on: August 02, 2017, 05:11:33 AM »
|
|
|
This Unitronics is no longer with us, i threw it out as the BDM Pads fell off, and was unable to fix the ports as i tried..
|
|
|
|
|
Logged
|
|
|
|
focalpoint519
Full Member
Karma: +29/-65
Offline
Posts: 148
|
|
« Reply #14 on: August 02, 2017, 10:47:35 AM »
|
|
|
If you need another ECU i have a couple MED 9.1's with Cruise control map switching ecus on my webs tore, or ebay, if your in Canada i can express ship you one (free shipping)
|
|
|
|
« Last Edit: August 02, 2017, 10:49:06 AM by focalpoint519 »
|
Logged
|
|
|
|
|
