Pages: 1 2 [3]
Author Topic: ESKONF detection tool  (Read 62531 times)
360trev
Full Member
***

Karma: +68/-2
Offline Offline

Posts: 235


« Reply #30 on: October 12, 2018, 10:00:55 AM »

Here's the output on a Ferrari rom...

Code:
-[ ESKONF Configuration of power stage (actuators) ]-------------------------------------------

>>> Scanning for ESKONF Lookup code sequence...

found needle at offset=0x58336

 1. Configuration of output stages
 =================================
 The configuration is made with the Label ESKONF_R (right bank) & ESKONF_L (left bank), each by 7 bytes.

 Every byte is standing for 4 output stages. Therefore every output stage has got 2 consecutive
 configuration Bits.

 Enable of the output stages diagnosis
 -------------------------------------
 With the configurations-Bytes in ESKONF the functions have to be set active / inactive depending
 on the available components in the car. At the same time with the 2 Bits the function of the
 diagnosis is set.

 Assignment of the Bit pattern:
 ------------------------------
 00  Diagnosis active with OBDII-malfunction storage with test of healing
 01  Diagnosis active without OBDII-malfunction storage with test of healing
 10  Diagnosis active without OBDII-fault memory without test of healing (EKP)
 11  Diagnosis not active


ESKONF_L @ ADR:0x810ae4 (offset 0x10ae4) - Left Bank Configuration
----------+----------------------------------------------------------------------
[i] Hex   |           Bit
          | 76     54     32     10
----------+----------------------------------------------------------------------
          | EV4    EV3    EV2    EV1
[0] 0x00  | 00     00     00     00
          | M52    M03    M35    M19
          +----------------------------------------------------------------------
          | M52   Cylinder 6 injector control power output
          | M03   Cylinder 8 injector control power output
          | M35   Cylinder 7 injector control power output
          | M19   Cylinder 5 injector control power output
----------+----------------------------------------------------------------------
          | LSHVK1 xxxx   TEV    MIL
[1] 0x33  | 00     11     00     11
          | M34    M21    M05    F46
          +----------------------------------------------------------------------
          | M34   LH rear Lambda sensor heater (duty cycle) Power output
          | M21   Not Used
          | M05   Control for LH canister purge valve (duty cycle) Power output
          | F46   Not Used
----------+----------------------------------------------------------------------
          | EKP    LUE1   LSHVK2 MIL
[2] 0xbf  | 10     11     11     11
          | F30    F50    M02    F02
          +----------------------------------------------------------------------
          | F30   Fuel pump control Digital output
          | F50   Not Used
          | M02   Not Used
          | F02   Not Used
----------+----------------------------------------------------------------------
          | --     --     KOS    LUE2
[3] 0xff  | 11     11     11     11
          | Fxx    Fxx    F13    F62
          +----------------------------------------------------------------------
          | Fxx   Not Used
          | Fxx   Not Used
          | F13   Not Used
          | F62   Not Used
----------+----------------------------------------------------------------------
          | xxxx   SU1    NWS    xxxx
[4] 0xfc  | 11     11     11     00
          | M53    M04    M36    M20
          +----------------------------------------------------------------------
          | M53   Not Used
          | M04   Not Used
          | M36   Not Used
          | M20   Control for LH exhaust by-pass power output
----------+----------------------------------------------------------------------
          | xxxx   xxxx   xxxx   xxxx
[5] 0xff  | 11     11     11     11
          | F18    F33    F34    F01
          +----------------------------------------------------------------------
          | F18   Not Used
          | F33   Not Used
          | F34   Not Used
          | F01   Not Used
----------+----------------------------------------------------------------------
          | xxxx   xxxx   xxxx   xxxx
[6] 0xff  | 11     11     11     11
          | M13    M13    M45    M45
          +----------------------------------------------------------------------
          | M13   Not Used
          | M13   Not Used
          | M45   Not Used
          | M45   Not Used
----------+----------------------------------------------------------------------


ESKONF_R @ ADR:0x810aeb (offset 0x10aeb) - Right Bank Configuration
----------+----------------------------------------------------------------------
[i] Hex   |           Bit
          | 76     54     32     10
----------+----------------------------------------------------------------------
          | EV4    EV3    EV2    EV1
[0] 0x00  | 00     00     00     00
          | M52    M03    M35    M19
          +----------------------------------------------------------------------
          | M52   Cylinder 2 injector control power output
          | M03   Cylinder 4 injector control power output
          | M35   Cylinder 3 injector control power output
          | M19   Cylinder 1 injector control power output
----------+----------------------------------------------------------------------
          | LSHVK1 xxxx   TEV    MIL
[1] 0x33  | 00     11     00     11
          | M34    M21    M05    F46
          +----------------------------------------------------------------------
          | M34   RH rear Lambda sensor heater (duty cycle) power output
          | M21   Not Used
          | M05   Control for RH canister purge valve (duty cycle) power output
          | F46   Not Used
----------+----------------------------------------------------------------------
          | EKP    LUE1   LSHVK2 MIL
[2] 0xbf  | 10     11     11     11
          | F30    F50    M02    F02
          +----------------------------------------------------------------------
          | F30   Fuel pump control digital output
          | F50   Not Used
          | M02   Not Used
          | F02   Not Used
----------+----------------------------------------------------------------------
          | --     --     KOS    LUE2
[3] 0xf3  | 11     11     00     11
          | Fxx    Fxx    F13    F62
          +----------------------------------------------------------------------
          | Fxx   Not Used
          | Fxx   Not Used
          | F13   A/C compressor control digital output
          | F62   Secondary air pump control digital output
----------+----------------------------------------------------------------------
          | xxxx   SU1    NWS    xxxx
[4] 0x00  | 00     00     00     00
          | M53    M04    M36    M20
          +----------------------------------------------------------------------
          | M53   Modular manifolds control power output
          | M04   Compensation throttle control power output
          | M36   Timing variator control  Digital output
          | M20   Control for RH exhaust by-pass power output
----------+----------------------------------------------------------------------
          | xxxx   xxxx   xxxx   xxxx
[5] 0x3f  | 00     11     11     11
          | F18    F33    F34    F01
          +----------------------------------------------------------------------
          | F18   Canister closing control power output
          | F33   Not Used
          | F34   Secondary air valve control digital output
          | F01   Not Used
----------+----------------------------------------------------------------------
          | xxxx   xxxx   xxxx   xxxx
[6] 0xff  | 11     11     11     11
          | M13    M13    M45    M45
          +----------------------------------------------------------------------
          | M13   Not Used
          | M13   Not Used
          | M45   Not Used
          | M45   Not Used
----------+----------------------------------------------------------------------

Logged
TurboMMJ
Newbie
*

Karma: +0/-4
Offline Offline

Posts: 22


« Reply #31 on: October 28, 2020, 07:01:17 AM »

SUCH A NICE TOOL TO HAVE !

AFTER READING MY FILE THERE IS ESKONF 0 AND ESKONF 1 , BOTH HAS TO BE CODED IS THAT RIGHT TO DELETE SAI,... ,etc.  ?

see attached please
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425



« Reply #32 on: October 28, 2020, 07:25:26 AM »

Yes
Logged
sonique
Sr. Member
****

Karma: +24/-12
Offline Offline

Posts: 283


« Reply #33 on: October 28, 2020, 04:24:03 PM »

SUCH A NICE TOOL TO HAVE !

AFTER READING MY FILE THERE IS ESKONF 0 AND ESKONF 1 , BOTH HAS TO BE CODED IS THAT RIGHT TO DELETE SAI,... ,etc.  ?

see attached please

this file only one
tool not good
Logged
mdccode5150
Full Member
***

Karma: +13/-4
Offline Offline

Posts: 122


« Reply #34 on: October 28, 2020, 09:27:31 PM »

Question: about which ESKONF is for my car (LOGIC would say, and would have to be ESKONF_1) 2002 ALMS AUDI TT 225HP NO VVT am I right? and ESKONF_0 has NO ZUE=Ignition coils! I don't know what the purpose of this would be?

Searching for ESKONF (Bosch ME7.5) in file: ori.bin
## ESKONF_0 (Addr:000044B3) -- FF FF 00 F0 3F F0 2C
b0:FF    ZUE4(95)..:N(11)    ZUE3(94)..:N(11)    ZUE2(103).:N(11)    ZUE1(102).:N(11)   ZUE=Ignition coil
b1:FF    NC........:N(11)    NC........:N(11)    NC........:N(11)    NC........:N(11)
b2:00    EV4(89)...:Y(00)    EV3(88)...:Y(00)    EV2(97)...:Y(00)    EV1(96)...:Y(00)   EV=Fuel injector
b3:F0    LSHHK(63).:N(11)    EFLA(48)..:N(11)    LDR(104)..:Y(00)    TEV(64)...:Y(00)   LSHHK=Rear O2, EFLA=Error lamp, LDR=N75, TEV=N80 purge valve
b4:3F    BKV(22)...:Y(00)    NC(24)....:N(11)    AAV(116)..:N(11)    MIL(47)...:Y(00)   BKV=Brake booster pump, AAV=Shutoff valve, MIL=OBD lamp
b5:F0    NC........:N(11)    NC........:N(11)    EKP(65)...:Y(00)    SLP(66)...:Y(00)   EKP=Fuel pump, SLP=J299 SAI pump
b6:2C    ULT(105)..:Y(00)    UAGR(114).:S(10)    SLV(9)....:N(11)    NWS(115)..:Y(00)   ULT=N249 wg valve, UAGR=EGR valve, SLV=N112 SAI relay, NWS=n205 VVT

=================================================================================================================

## ESKONF_1 (Addr:000151E2) -- AA FF 00 30 F3 F8 33

b0:AA    ZUE4(95)..:S(10)    ZUE3(94)..:S(10)    ZUE2(103).:S(10)    ZUE1(102).:S(10)   ZUE=Ignition coil
b1:FF    NC........:N(11)    NC........:N(11)    NC........:N(11)    NC........:N(11)
b2:00    EV4(89) ...:Y(00)    EV3(88)...:Y(00)    EV2(97)...:Y(00)    EV1(96)...:Y(00)   EV=Fuel injector
b3:30    LSHHK(63) .:Y(00)    EFLA(48)..:N(11)    LDR(104)..:Y(00)    TEV(64)...:Y(00)   LSHHK=Rear O2, EFLA=Error lamp, LDR=N75, TEV=N80 purge valve
b4:F3    BKV(22)...:N(11)    NC(24)....:N(11)    AAV(116)..:N(11)    MIL(47)...:Y(00)   BKV=Brake booster pump, AAV=Shutoff valve, MIL=OBD lamp
b5:F8    NC........:N(11)    NC........:N(11)    EKP(65)...:S(10)    SLP(66)...:Y(00)   EKP=Fuel pump, SLP=J299 SAI pump
b6:33    ULT(105)..:Y(00)    UAGR(114).:N(11)    SLV(9)....:Y(00)    NWS(115)..:N(11)   ULT=N249 wg valve, UAGR=EGR valve, SLV=N112 SAI relay, NWS=n205 VVT

11 = OFF       (EFLA=Error lamp, BKV=Brake booster pump, AAV=Shutoff valve, BKV=Brake booster pump, AAV=Shutoff valve, UAGR=EGR valve, NWS=n205 VVT)
00 = ON        (Injectors, LSHHK=Rear O2, LDR=N75, TEV=N80 purge valve, MIL=OBD lamp, SLP=J299 SAI pump, ULT=N249 wg valve, SLV=N112 SAI relay)
10 = Special   (ZUE=Ignition coil, EKP=Fuel pump,)
Logged
mdccode5150
Full Member
***

Karma: +13/-4
Offline Offline

Posts: 122


« Reply #35 on: December 06, 2020, 05:22:25 PM »

After some research reading definition files, Tuning S4 ESKONF, and playing around with ME7.5, and Porsche's ME7.1.1 ESKONF Bits with success I put this cheat sheet together. Maybe it'll help someone. Let me know if there is mistakes or more information...Thanks!

I posted here: http://nefariousmotorsports.com/forum/index.php?topic=18803.0title=

TITLE: ME7.5 Cheat Sheet and Templates for ESKONF BITS (Disabling Outputs/Devices) Diagnostics
« Last Edit: December 06, 2020, 05:46:13 PM by mdccode5150 » Logged
mdccode5150
Full Member
***

Karma: +13/-4
Offline Offline

Posts: 122


« Reply #36 on: December 06, 2020, 05:47:03 PM »

After some research reading definition files, Tuning S4 ESKONF, and playing around with ME7.5, and Porsche's ME7.1.1 ESKONF Bits with success I put this cheat sheet together. Maybe it'll help someone. Let me know if there is mistakes or more information...Thanks!

I posted here: http://nefariousmotorsports.com/forum/index.php?topic=18803.0title=

TITLE: ME7.5 Cheat Sheet and Templates for ESKONF BITS (Disabling Outputs/Devices) Diagnostics

Made a small change
Logged
TeknoFi
Full Member
***

Karma: +1/-3
Offline Offline

Posts: 85


« Reply #37 on: October 04, 2022, 10:50:39 AM »

great little tool, thank you.
Logged
RetardedTiming
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 15


« Reply #38 on: March 08, 2023, 09:21:17 PM »

After some research reading definition files, Tuning S4 ESKONF, and playing around with ME7.5, and Porsche's ME7.1.1 ESKONF Bits with success I put this cheat sheet together. Maybe it'll help someone. Let me know if there is mistakes or more information...Thanks!

I posted here: http://nefariousmotorsports.com/forum/index.php?topic=18803.0title=

TITLE: ME7.5 Cheat Sheet and Templates for ESKONF BITS (Disabling Outputs/Devices) Diagnostics

I have an Audi TT 1.8T ATC 180HP 8N0906018S and trying to delete O2 sensors, is this correct ESKONF? http://nefariousmotorsports.com/forum/index.php?topic=9178.0title= Someone on this post said? "Early files have no coil circuit diagnosis."

Code:
Reading file [TT.bin] to buffer...
Buffer ready... Filesize:524288 (0x80000)

Searching for ESKONF (Bosch ME7.5) in file: TT.bin
## ESKONF_0 (Addr:000280FB) -- FF FF 00 F0 3F F0 2C
b0:FF    ZUE4(95)..:N(11)    ZUE3(94)..:N(11)    ZUE2(103).:N(11)    ZUE1(102).:N(11)   ZUE=Ignition coil
b1:FF    NC........:N(11)    NC........:N(11)    NC........:N(11)    NC........:N(11)
b2:00    EV4(89)...:Y(00)    EV3(88)...:Y(00)    EV2(97)...:Y(00)    EV1(96)...:Y(00)   EV=Fuel injector
b3:F0    LSHHK(63).:N(11)    EFLA(48)..:N(11)    LDR(104)..:Y(00)    TEV(64)...:Y(00)   LSHHK=Rear O2, EFLA=Error lamp, LDR=N75, TEV=N80 purgevalve
b4:3F    BKV(22)...:Y(00)    NC(24)....:N(11)    AAV(116)..:N(11)    MIL(47)...:Y(00)   BKV=Brakebooster pump, AAV=Shutoff valve, MIL=OBD lamp
b5:F0    NC........:N(11)    NC........:N(11)    EKP(65)...:Y(00)    SLP(66)...:Y(00)   EKP=Fuel pump, SLP=J299 SAI pump
b6:2C    ULT(105)..:Y(00)    UAGR(114).:S(10)    SLV(9)....:N(11)    NWS(115)..:Y(00)   ULT=N249 wg valve, UAGR=EGR valve, SLV=N112 SAI relay, NWS=n205 VVT
Logged
Pages: 1 2 [3]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.023 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)