NefMoto > Technical > Tuning > Tune Audi A3 2.0 TFSI
Pages: 1 [2]
« previous next »
Author Topic: Tune Audi A3 2.0 TFSI  (Read 12138 times)
prj
Hero Member
*****

Karma: +979/-433
Offline Offline

Posts: 5871
« Reply #15 on: October 16, 2017, 12:34:43 AM »
Quote from: gman86 on October 15, 2017, 01:18:52 PM
Check the linkage arm hasn't been disconnected. It's not wise to delete the flaps if they still exist unless you can pin them open. In which case, the flaps can be deleted in SW
And lose a ton of low down torque, it's not TDI.
Logged
PM's will not be answered, so don't even try.
Log your car properly.
Kacza
Full Member
***

Karma: +20/-6
Offline Offline

Posts: 213
« Reply #16 on: October 16, 2017, 02:54:21 AM »
In the measurement blocks I see that Intake Manifold Flaps are working.

DTCs are when the engine is cold. This is usually the morning. Later when the engine is warm and I will delete the DTC they will not come back.
Logged
Kacza
Full Member
***

Karma: +20/-6
Offline Offline

Posts: 213
« Reply #17 on: October 16, 2017, 11:18:20 AM »
Guys one question. Cheesy
How to interpret these two maps?
Is this LDRXN and LDRXNZK?
These maps are very similar.
I think the LDRXNZK should be set lower.
Logged
tfsikiller
Jr. Member
**

Karma: +1/-1
Offline Offline

Posts: 41
« Reply #18 on: October 16, 2017, 11:37:18 AM »
Quote from: Kacza on October 16, 2017, 11:18:20 AM
Guys one question. Cheesy
How to interpret these two maps?
Is this LDRXN and LDRXNZK?
These maps are very similar.
I think the LDRXNZK should be set lower.

From the picture it looks correct.
Though there're usually multiple ldrxn maps based on cars configuration. Example... if your car has tiptronic, dsg, manual trans, they use different ldrxn.

In my map ldrxn and ldrxnzk are right next to eachother.
Logged
ReproLogic
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 21
« Reply #19 on: October 16, 2017, 01:55:10 PM »
LDRXNZK are limit load in Knocking, and LDRXNLB limit load in open intake flaps.
Logged
tfsikiller
Jr. Member
**

Karma: +1/-1
Offline Offline

Posts: 41
« Reply #20 on: October 16, 2017, 07:56:59 PM »
Quote from: ReproLogic on October 16, 2017, 01:55:10 PM
LDRXNZK are limit load in Knocking, and LDRXNLB limit load in open intake flaps.

Good to know... so your saying if a fault is detected from intake flaps, it can lower boost? Like limp mode?
Logged
Kacza
Full Member
***

Karma: +20/-6
Offline Offline

Posts: 213
« Reply #21 on: October 17, 2017, 12:17:09 AM »
Quote from: ReproLogic on October 16, 2017, 01:55:10 PM
LDRXNZK are limit load in Knocking, and LDRXNLB limit load in open intake flaps.

Does my file in the first post have an LDRXNLB map?

He has only two LDRXN load maps at 1CD860 and 1CD8A2 addresses.
Logged
ReproLogic
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 21
« Reply #22 on: October 17, 2017, 01:08:24 AM »
Quote from: tfsikiller on October 16, 2017, 07:56:59 PM
Good to know... so your saying if a fault is detected from intake flaps, it can lower boost? Like limp mode?

No , for limp mode are another LDR, like LDORXN... LDRXNLB are used when the flaps open. I´m talking about MED 17.5.
Logged
Kacza
Full Member
***

Karma: +20/-6
Offline Offline

Posts: 213
« Reply #23 on: October 27, 2017, 02:38:34 AM »
Quote from: ReproLogic on October 17, 2017, 01:08:24 AM
I´m talking about MED 17.5.
Can you tell me what maps I need to stage 1 MED17?
Logged
Pages: 1 [2]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • June 04, 2024, 03:48:54 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 15 queries. (Pretty URLs adds 0s, 0q)