Pages: [1]
Author Topic: NefMoto ME7 ECU Flasher: Validation failed  (Read 7148 times)
iborisov
Jr. Member
**

Karma: +0/-2
Offline Offline

Posts: 41



« on: November 22, 2017, 06:03:32 AM »

Hey Everyone,

I get the following error when i had to do a full read of the ECU; Validation failed, ECU reports RequestUpload service is not supported. RequestUpload may have been disabled by aftermarket engine software.

I try it on two cars Audi A3 1.8TQ 1999 and Audi A4 1.8TQ 2002 both stock.

I have tried playing with the baud rates, tried slow and fast int(fast didnt work at all). I tried each memory layout with different baud rates. I can read ecu Info with no issues.

Current setup: Windows 7 x64, FT232R USB UART cable.

I wonder if there is a problem with the driver or a problem with the cable or software...

And a question:

If I can not Full Read the software, is that means 100% I will not be able to Full Write a new software? I am scared to try Full Write...

#######FULL READ FLASH LOG: #############
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Timing negotiation failed. Communication timings are unchanged.
Requesting security access.
Security access granted.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Validation failed, ECU reports RequestUpload service is not supported. RequestUpload may have been disabled by aftermarket engine software.
Memory layout validation failed.
Starting to read data block.
Requesting upload from ECU for address range 0x00800000 to 0x00803FFF.
Request upload from ECU failed, ECU reports service is not supported. Request upload may have been disabled by aftermarket engine software.
Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete.
Finished forcing ECU to recognize that failed read operation is complete.
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.

Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #1 on: November 22, 2017, 11:06:51 AM »

Request upload from ECU failed, ECU reports service is not supported. Request upload may have been disabled by aftermarket engine software.
Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete.
Finished forcing ECU to recognize that failed read operation is complete.
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.

You claim they are stock, but are you sure?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
iborisov
Jr. Member
**

Karma: +0/-2
Offline Offline

Posts: 41



« Reply #2 on: November 23, 2017, 01:20:30 AM »

You claim they are stock, but are you sure?

Yes, I think they are original. I attached one of the files which I was able to read with MPPSv17.

Would you check if it's an original?

And would you give any opinion on this: If I can not Full Read the software, is that means 100% I will not be able to Full Write a new software?


Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #3 on: November 23, 2017, 12:51:54 PM »

If you are going to flash over them anyway, boot mode them to stock. I do not have every file floating around to check if your particular file is stock; get the stock file and compare it yourself using md5sum or just flash it to your ecu.

Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.025 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)