Pages: 1 ... 4 5 [6] 7 8 9
Author Topic: ME 3.8.3  (Read 169001 times)
pvl
Sr. Member
****

Karma: +32/-1
Offline Offline

Posts: 350


« Reply #75 on: April 28, 2013, 05:13:08 AM »

Try it, and you will see.

TOO much info already about this on this forum.

Use the searchfunction and you will find a LOT of handy info on this matter.

Regards,

PvL
Logged
Dobermann
Full Member
***

Karma: +7/-0
Offline Offline

Posts: 80


« Reply #76 on: April 28, 2013, 05:01:56 PM »

Try it, and you will see.

TOO much info already about this on this forum.

Use the searchfunction and you will find a LOT of handy info on this matter.

Regards,

PvL


i have use the search button !! i found a lot of info but nothing about the MPPS Connector !!

problem is solved now !! all work without problems !

the K line had not good connection

writing time in fast mode 2 min 30 sec and normal mode 3 min with V16

BR
Logged
pvl
Sr. Member
****

Karma: +32/-1
Offline Offline

Posts: 350


« Reply #77 on: April 29, 2013, 01:48:47 AM »

Thanks for your feedback,

My V12 does it also in 3min, but i never used the fast mode for this.
Perhaps today on a  AJH-Seat-Alhambra from 2000 i can test it out.
Hopefully i can also use the fast mode with the v12 version of MPPS.

PvL
Logged
Foti
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #78 on: May 25, 2013, 01:38:12 PM »

I am trying to attempt tuning/flashing my 1999 A4 with the 1.8t AEB engine. I have an extra 8D0907558M ecu I bought so I still have the OEM untouched.

I found a partial definition file for this controller. One big item I noticed was the MAF table was missing. After looking around the A3 1.8t definition file (557B) I think I found where the table resides. Am I on the right track?

David
Logged
Foti
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #79 on: May 28, 2013, 08:27:50 PM »

Another discovery. My 558M's flash is not labeled the same as the 557P (29f200b).

I am going to see if I can get an eprom reader from work as I'd like to make sure I have the correct file to start with.
Logged
prj
Hero Member
*****

Karma: +1072/-481
Offline Offline

Posts: 6037


« Reply #80 on: May 29, 2013, 01:01:30 AM »

Doesn't really matter, should be the same chip...
Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
Foti
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #81 on: June 09, 2013, 08:37:52 PM »

I successfully flashed the ECU and the car runs as expected. However, I had a P0601 code.

I was able to resolve this by disconnecting the 12V from Pin 43 before I turned the IGN off after flashing.

Logged
Foti
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #82 on: June 26, 2013, 08:01:32 PM »

The 601 code is appearing after running the engine. WinOLS says checksum is ok. Ideas?
Logged
Foti
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #83 on: June 27, 2013, 11:30:10 AM »

Sorry, 601 code is checksum error.

I still don't have a good understanding of what it is and how it works. The car has been running with the error, so far at least.
Logged
automan001
Full Member
***

Karma: +47/-0
Offline Offline

Posts: 153


« Reply #84 on: December 06, 2013, 05:56:12 AM »

Publishing comparison of AEB (150 HP) and AJL (180 HP) firmwares.
It's M3.8.2 BUT is very helpful to find out where to start tuning Cool
« Last Edit: July 16, 2014, 02:48:49 AM by automan001 » Logged
eliotroyano
Hero Member
*****

Karma: +48/-8
Offline Offline

Posts: 826


« Reply #85 on: July 21, 2014, 05:18:46 PM »

Here is another little guide based in a simple Stage 1 tuned file and a limited map pack (OLSx). It is for M382 but the idea is the same. I hope you find it useful --> https://www.olsx.lu/getpage.asp?p=limited_map_pack
Logged
gezame
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 6


« Reply #86 on: August 05, 2014, 05:21:08 PM »

Hi
Audi A3 8L 1.8T AGU,  flash 29f200AB bench write-ok with Mpps, 3,33m.
06A906018AQ - 0261204678 - 1037359525  Bosch M3.8.3
Logged
eliotroyano
Hero Member
*****

Karma: +48/-8
Offline Offline

Posts: 826


« Reply #87 on: August 05, 2014, 05:31:53 PM »

Hi
Audi A3 8L 1.8T AGU,  flash 29f200AB bench write-ok with Mpps, 3,33m.
06A906018AQ - 0261204678 - 1037359525  Bosch M3.8.3

Bench was ok, great but do you test it flash in car?
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601


« Reply #88 on: August 06, 2014, 01:08:55 AM »

works in car over here
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601


« Reply #89 on: August 13, 2014, 11:20:14 AM »

does anybody know how to delete errors in this older motronics?

would like to remove 18259 - Powertrain Data Bus: Missing Message from ABS Controller P1851 - 35-10
Logged
Pages: 1 ... 4 5 [6] 7 8 9
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.037 seconds with 17 queries. (Pretty URLs adds 0s, 0q)