Pages: 1 ... 6 7 [8] 9
Author Topic: ME 3.8.3  (Read 157604 times)
MK2-VRT
Full Member
***

Karma: +2/-10
Offline Offline

Posts: 131


« Reply #105 on: December 15, 2014, 07:56:55 AM »

Always desolder the eeprom mate, works oke, also with china carprog.

When you see the 2 the same lines on 0x000 and 0x060, then only do the 50 - 9E trick.

You see the same lines on 0x000 and 0x040, then do the 50 trick and correct the checksums.

I make 50 a 100 from this ecu's immo off and works like charm, never had a problem with it.

Good luck..
Logged
jona29
Newbie
*

Karma: +1/-1
Offline Offline

Posts: 22


« Reply #106 on: December 21, 2014, 03:59:00 PM »

thanks for the reply but i dont know the  50- 9e trick you refer to , also how do i correct the checksumm on this eeprom ? this is the first old ecu ive ever had to immo off tbh 
Logged
jona29
Newbie
*

Karma: +1/-1
Offline Offline

Posts: 22


« Reply #107 on: December 21, 2014, 04:05:10 PM »

ive attached a read of the chip . ecu is vw : 071 906 018 K
Logged
eliotroyano
Hero Member
*****

Karma: +47/-7
Offline Offline

Posts: 796


« Reply #108 on: December 21, 2014, 09:02:01 PM »

ive attached a read of the chip . ecu is vw : 071 906 018 K

Please confirm.
Logged
MK2-VRT
Full Member
***

Karma: +2/-10
Offline Offline

Posts: 131


« Reply #109 on: December 27, 2014, 05:00:13 AM »

Immo off
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #110 on: January 12, 2015, 08:29:05 AM »


I want to make an ECU upgrade to 06A906018CG(me3.8.3) from 8D0907557T(me3.8.2)
Is it possible?
Logged
eliotroyano
Hero Member
*****

Karma: +47/-7
Offline Offline

Posts: 796


« Reply #111 on: January 15, 2015, 10:19:27 AM »

I want to make an ECU upgrade to 06A906018CG(me3.8.3) from 8D0907557T(me3.8.2)
Is it possible?

Hi Grey, both ECUs have similar pinouts. Internally are very similar too. In haven't tested it compatibility but I have read about some people changing 557xx ECU for 018CG ones with great sucess.
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #112 on: January 15, 2015, 10:25:46 AM »

Hi Grey, both ECUs have similar pinouts. Internally are very similar too. In haven't tested it compatibility but I have read about some people changing 557xx ECU for 018CG ones with great sucess.

Thanks Elio,

I will try and report to here.
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #113 on: January 18, 2015, 02:56:54 PM »

Passat worked with ECU ME3.8.3 (06A906018CG)

But i have 2 fault codes;

18044 - Powertrain Data Bus
            P1636 - 35-00 - Missing Message from Airbag Controller
18259 - Powertrain Data Bus
            P1851 - 35-00 - Missing Message from ABS Controller

What should I do now?



Logged
eliotroyano
Hero Member
*****

Karma: +47/-7
Offline Offline

Posts: 796


« Reply #114 on: January 18, 2015, 04:38:18 PM »

Passat worked with ECU ME3.8.3 (06A906018CG)
But i have 2 fault codes;
18044 - Powertrain Data Bus
            P1636 - 35-00 - Missing Message from Airbag Controller
18259 - Powertrain Data Bus
            P1851 - 35-00 - Missing Message from ABS Controller
What should I do now?

Tayfun did you recode CAN Gateway to same value you had in previous ECU? Airbag and ABS module are not communicating with ECU.
Logged
lp2015
Newbie
*

Karma: +1/-8
Offline Offline

Posts: 13


WWW
« Reply #115 on: May 24, 2015, 05:47:53 PM »

Hello friends, I'm in trouble with my ecu, and I want to tell me what happens.

I can not perform loads of programs through the diagnostic port, only soldering and unsoldering memory.

I read all the forum and all the steps but did not find the problem.

I am analyzing the hardware for problem with my ecu.

I have an AM29f200BB memory functioning properly.

The ecu is Bosch 3.8.3 and data accompanying it:

Bosch Software Number: 1037352127
Hardware Bosch Number: 0261206518
VW software Number: 06A906018MK
System Type Number; 06A906018CG

There is the possibility that the ecu come blocked or something for no charge for OBD2?

I tried on bench and in the car without success

I informed the Security Access Denied.

Thanks
Logged

technic
Full Member
***

Karma: +17/-5
Offline Offline

Posts: 227


« Reply #116 on: May 26, 2015, 12:16:47 PM »

Put ecu pin 43 to +12V
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #117 on: June 04, 2015, 12:38:35 AM »

Tayfun did you recode CAN Gateway to same value you had in previous ECU? Airbag and ABS module are not communicating with ECU.

Now it works,thanks Elio Smiley
Logged
reset
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 17


« Reply #118 on: December 22, 2015, 05:37:47 PM »

Immo off

Does that really work?

Every one I've ever done has a checksum correction where you wrote "9E" (0x0E and 0x6E).
Since the original value at the cs location is 2A, shouldn't the new value be 7A and not 9E? (A0-50h=50h so 2A+50h=7A)

How does that work with 9E in the CS location? (that's not a valid checksum correction?)
Logged
ktm733
Hero Member
*****

Karma: +18/-8
Offline Offline

Posts: 660



« Reply #119 on: December 20, 2016, 06:40:04 PM »

Most people do NOT read and do NOT use the searchfunction. Thats a pitty.
I did, and the outcome was quite predictable. My own made bench-harness works
a treat.

If you get ANY errors, recheck your wiring, power and computer.

Did you have any success flashing other ecu's with your mpps before ?!?!? or is this
the first one you take-on ?

First be sure your equipment is o.k.

If problems still persist..  post here....

I steal power off the car's battery..  And mpps always tells me the voltage...  Be sure this
is above 12.0v and not above 13v.  Don't use cheap-ass powersupplies..  Use the battery
of the car instead. A friend had issues untill he finally took my advice on the carbattery
and suddenly it worked-out !!!

Best of luck,

PvL

 Hate to mess with an old post but you just saved me a couple hours of pulling out my hair. Thank you!
Logged
Pages: 1 ... 6 7 [8] 9
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.024 seconds with 17 queries. (Pretty URLs adds 0s, 0q)